manualshive.com logo in svg

Directed Electronics 3100, Руководство по установке

Поделиться
Скачать
Directed Electronics 3100 Скачать руководство пользователя страница 12

10

© 2011 Directed Electronics. All rights reserved.

remote to set the feature to the LED On option.  To set the LED 
Off, while still holding the Valet button, press 

AUX

AUX

.* (See Feature 

Table)

5.  Release the Valet button to exit programming, or repeat the above 

to program more features.

* Press 

  or 

AUX

 on the 

3-button

 remote to set the feature to 

the LED Off option.

Exit Programming

The siren emits one quick chirp, and then another lengthier chirp when exiting. 

Programming is exited when one of the following occurs:

•  Turn ignition ON
•  Close the doors
•  Press Valet button too many times
•  15 seconds or more lapses between steps

Feature Table

Valet but-

ton presses

( C h i r p s /

Flashes)

LED ON OPTION*

1 chirp

LED OFF OPTION

2 chirps

1

Active Arming

Passive Arming

2

Confirmation Chirps ON

Confirmation Chirps OFF

3

Ign-controlled Locking ON

Ign-controlled Locking OFF

4

Active Locking

Passive Locking

5

0.8 Second Doorlock Pulse 

3.5 Second Door Lock Pulse

6

Double Pulse Unlock OFF

Double Pulse Unlock ON

7

Code Hopping ON

Code Hopping OFF

8

Door Trigger Error Chirp ON

Door Trigger Error Chirp OFF

9

Double Pulse Lock OFF

Double Pulse Lock ON

Содержание 3100

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды