manualshive.com logo in svg

Directechs HK18, Руководство по установке, Страница: 17 / 23

Поделиться
Скачать
Directechs HK18 Скачать руководство пользователя страница 17

LED diagnostics and troubleshooting

This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation.

Module programming

LED

Description

Troubleshooting

Off

Module has no power.

Make sure the D2D harness is connected and that 12 Volt is present between the red and black 

wires. If 12 Volt is present, the module may be defective.

Solid red

Waiting to begin the programming 

sequence.

Ensure the correct programming procedure is being followed.

  

Flashes red & 
green

Initialization failed.

Reset the module and complete the programming again. If the issue persists, please contact 

Technical Support.

Solid orange

Transponder functions were skipped.

(If compatible) when the RXT mode is not desired or convenience features are needed, please 

reset and reprogram the module.

Flashes green

All required CAN networks has been 

detected.

Normal operation.

Flashes orange

1 of 2 CAN networks has been detected. Normal operation.

Flashes orange 
slowly

Key2GO initiated.

Please follow the steps indicated in "Module programming" on page 16 to complete the 

Key2GO programming.

Solid green x 
3 secs

Module was successfully programmed 

with all functions.

Normal operation.

Solid orange x 
3 secs

Module was successfully

programmed without transponder 

functions.

Normal operation.

Module programming – Error codes

LED

Description

Troubleshooting

Flashes red x 1

CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus 

by turning the ignition on and try again. If your installation does not require this connection, skip 

this step by pressing the programming button 5 times.

Flashes red x 1

J1850 not detected.

Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try 

again.

Flashes red x 2

CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the 

ignition on and try again. If your installation does not require this connection, skip this step by 

pressing the programming button 5 times.

Flashes red x 3

Bypass data not detected.

Check the bypass line connection. If more than one wire is used, make sure they are not inverted. 

Ensure the vehicle still operates correctly using the factory key.

Flashes red x 4

Bypass processing error.

The bypass calculation failed. Reset the module and try again. If the condition persists, please 

contact Technical Support.

Flashes red x 5

ISO 1 not detected.

The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & 

vehicle wiring reference charts)" on page 8 to check the connections.

Flashes red x 6

ISO 2 not detected.

The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams 

& vehicle wiring reference charts)" on page 8 to check the connections.

Flashes red x 7

MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to 

"Installation (wiring diagrams & vehicle wiring reference charts)" on page 8 to check the 

connections.

External module synchronization

LED

Description

Troubleshooting

  

  

(Flashes red, red, 
then orange) x 10

OBDII feature not supported.

The diagnostic data bus was not detected, therefore the SmartStart features will be limited.

Active Ground When Running (Status)

LED

Description

Troubleshooting

Flashes green

Ground When Running (Status) command 

received.

The module has initialized the remote start sequence. 

17

Directed Digital Solutions HK18

© 2019-09-20 Directed. All rights reserved.

Содержание HK18
























Отзывы:

Нет отзывов