PR
After pressing the power
switch a fourth time, the
display is horizontal and
inverted
PR
After pressing the power
switch a fifth time, the display
is vertical and facing away from
the resident
PR
After pressing the power
switch a sixth time, the display
is vertical and facing toward
the resident
Calibration & Accuracy Verification
• The device cannot be calibrated in the field by the
end user.
• If you suspect the device is providing inaccurate results,
use a second device to verify accuracy. Do not rely on
results you suspect to be inaccurate.
• Immediately discontinue use of the device if it provides
inaccurate readings.
Maintenance, Storage & Disposal
• Replace the battery as soon as the low-battery indicator
on the display screen is lit.
• Clean the surface of the device before it is used in
diagnosis of residents.
• Remove the battery if the device will not be used for an
extended period of time.
• Store the device in a place where ambient temperatures
range from -4º to 131ºF (-20º to 55ºC). A low-humidity
environment is recommended.
Cleaning
• Use a soft cloth dampened with 70% isopropyl alcohol to
clean the silicone that comes into contact with the finger
during testing. Also clean the finger using alcohol before
and after each test.
•
CAUTION
– Do not pour or spray any liquids
onto the device, and do not allow any liquid to enter
any openings in the device. Allow the device to dry
thoroughly before reusing.
Follow local ordinances and recycling instructions regarding
disposal or recycling of the device and device components,
including batteries.
Measurement Principle
The Oximeter is calibrated to display functional oxygen
saturation using the principles of the Lambert Beer Law,
according to Spectrum Absorption Characteristics of
Reductive Hemoglobin(R Hb) and Oxyhemoglobin
(O
2
Hb) in red and near-infrared zones. Using Photoelectric
Oxyhemoglobin Inspection Technology and Capacity
Pulse Scanning and Recording Technology, the Oximeter
measures SpO
2
and pulse rate by shining two beams
of differing wavelengths of light (660nm red and 940nm
near infrared) through the tip of the fingernail. The
Oximeter measures the amount of each wavelength
of light that passes through the fingernail using a
photosensitive element. The microprocessor analyzes
these measurements, determines the SpO
2
level and
pulse rate of the resident, and displays this information
on the LCD display.
Limited Warranty
We offer to you, as the original purchaser, a warranty for the Attendant Sock-Style Fingertip Pulse Oximeter. Our
warranty applies for the limited warranty period stated below. If any device or device part listed below is defective
in material or workmanship during the applicable limited warranty period, we will repair or replace it at our cost.
Please note that the decision to repair or replace a device or device part will be at our discretion. Our warranty
applies only if the device is properly maintained by the original purchaser for normal, indoor use and does not
cover normal wear and tear, modification of the device, or damage caused by abuse, improper use, failure to
maintain, use which exceeds the published device limitations, or the combination of any device with another
product. In addition, our warranty does not cover fading, colorfastness, stains, spills or exposure to chemicals,
odors, heat or light. In certain cases, we may provide you repair or adjustment instructions and/or replacement
parts and ask you to perform a repair or adjustment or replace a defective part.
Our warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Please note that our limited warranty period begins when we ship the device to you. The limited warranty
period and our obligations under the warranty end once you transfer the device to someone else or at the end
of the applicable limited warranty period identified below, whichever is earlier.
Warranty Period
(Parts)
Anticipated Usable
Device Life
Attendant Sock-Style Fingertip Pulse Oximeter
(excluding battery and accessories)
2 year
2 year
3
1-800-634-7328
DirectSupply.com
