background image

2

  WARNING.

    If you are inexperienced with basic r/c flight we strongly recommended you contact the nearest 

model aircraft club. Experienced members will help you to install additional accessories to put your 

aircraft airworthy. The club will ensure your training and you will avoid flying illegally and destroy 

your aircraft from the first flight.

  ADDITIONAL ITEMS REQUIRED.

  TOOLS AND SUPPLIES.

KIT CONTAIN.

•  Propulsion set depending your choice : 

gas or electric.

•  Radio set minimum 4 channels.

•  4 servos.

•  Propeller.

•  Electric lipo pack or Ni-Mh.

•  Switch or Bec controller and fuse.

•  Thick cyanoacrylate glue.

•  30 minute epoxy.

•  Electric drill.

•  Assorted drill bits.

•  Modelling knife.

•  Straight ruler. 

•  Miscellaneous sandpaper.

•  90° builder’s triangle.

•  Wire cutters.

•  Tape & T-pin

•  A set of small keys 6 section

•  A set of screw drivers

   

Thank you for choosing a 

Direct Airscale

 model. If you have any problems do not hesi-

tate to consult our website. Especially the section CLUB 

DA 

(

Direct Airscale

 club) for each 

plane where you will find information. You also can consult us directly by phone but try 

to be a maximum shorter        . Thank you. You also can participate in the interaction 

you’ll find at general chapter CLUB 

DA

.

     The RECREATION is the perfect aircraft to relax and, or, progress.Low wing for 

a neutral behavior and good reactivity.Facilitates learning inverted flight.Rectangu-

lar wing.Moderate dihedral. Good ratio length / size (0.84) for a good pitch toler-

ance and easy balancing. Tricycle to protect the propeller in case of global return sca-

brous. Large diameter wheels for tracks average. Logo 

DA

 (direct airscale) very visible 

to the underside (below) for tracking that will help you in your aerobatic training.A 

plane leisure without moderation. We kept an asymmetric biconvex profile for our 

Recreations to maintain good fault tolerance in particular variations of lift landing.

This is the plane that you will start to really play in the third dimension.

  CONGRATULATIONS.

•  Light and rigid balsa and plywood construc-

tion

•  Hull and wings constructed and covered

•  Clear canopy

•  1 Pilot included

•  Decoration sticker board

•  Rigid aluminium landing gear

•  Large wheels diameter

•  Controlled front wheel

•  Spinner

•  Gas engine accessories (tank, engine mount,...)

•  Electric engine accessories (lipo wooden part, 

mounting kit,...)

•  All neccessary hardware and accessories in-

cluded

•  Document for assembly (Several languages).

Содержание 2113























Отзывы: