Dionex ICS-900 Скачать руководство пользователя страница 95

Страница: 95 / 142

5 • Service

Doc. 065215-02 9/09

5.9

Replacing the Waste Valve Seal

A damaged seal causes leakage around the base of the waste valve knob.

1. Turn off the ICS-900 power switch.

2. To remove the waste valve from the pump head (see

Figure 5-12

), turn the

knob counterclockwise until it is loose, and then pull the knob straight out of
the cavity in the pump head.

3. If the seal is removed with the valve knob

Step 2

, pull the seal off the end of the

knob (see

Figure 5-13

). If the seal is not

removed with the valve knob, insert a thin
object (for example, the straightened end
of a paper clip) into the cavity in the
pump head and carefully pull out the seal.

Do not scratch the cavity.

Figure 5-13. Waste Valve Seal Replacement

Figure 5-12. Waste and Priming Valves

Scratches in the cavity will cause leaks around the base of the knob
while the pump is being primed.

Waste Valve

Seal

Valve Knob

Содержание ICS-900















































































































































Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды

Dionex ICS-900, Руководство оператора

Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды