Dionex ICS-3000 Скачать руководство пользователя страница 217

Страница: 217 / 392

8 • DP/SP Troubleshooting

Doc. 065031-04 1/08

201

backpressure, replace the component. Replace as many components as
necessary to resume operation at the standard operating backpressure.

8.16 Vacuum Degassing Module Low Vacuum

•

Leak in the vacuum degassing module

Check all tubing connections for leakage; tighten loose fitting connections.

8.17 Vacuum Degassing Module Does Not Run

•

Electrical connections incorrectly installed

There may be a problem with the connections from the vacuum degassing
module to the CPU board. Contact Dionex for assistance.

NOTE The ICS-3000 Ion Chromatography System electronics

components cannot be serviced by the user.

8.18 DP/SP Digital I/O Port Inoperative

•

TTL input-related error

1. The TTL input mode must match the signal type output by the device

connected to the pump. Check the user’s manual for the device to verify
that the correct signal type is selected.

2. A programming error occurred in the device sending the signal. Refer to

the user’s manual for the device for troubleshooting assistance.

•

TTL/Relay output-related error

1. A programming error occurred in the device sending the signal. Refer to

the user’s manual for the device for troubleshooting assistance.

2. The device being triggered may require a TTL input, not a relay. Connect

the device to a pump TTL output.

Содержание ICS-3000









































































































































































































































































































































































































Результаты поиска

Содержание ICS-3000

Отзывы:

Похожие инструкции для ICS-3000

Бренды по названию

Популярные бренды

Dionex ICS-3000, Руководство оператора

Результаты поиска

Содержание ICS-3000

Отзывы:

Похожие инструкции для ICS-3000

Бренды по названию

Популярные бренды