Dionex AS-HV Скачать руководство пользователя страница 74

Страница: 74 / 122

AS-HV Operator’s Manual

Doc. 065125-01 10/06

4. Reposition the track over the rotor and fix by slotting the track

occlusion pin back into the track slot.

NOTE Compressing the spring on the track occlusion

pin will increase the suction height and
performance against backpressure.

5. Connect the delivery line to the inlet nipple of the fixed rinse

reservoir (see

Figure B-3

). Keep the delivery line as short as possible.

6. Connect the suction line to the reservoir containing rinse fluid. Keep

the suction line as short as possible.

NOTE Dionex recommends using ASTM Type I (or

better) filtered, deionized water as the rinse
fluid.

To remove tubing from the rinse pump:

•

Release the track by disengaging the track occlusion arm.

•

Remove both tubing bridges from their location slots and remove the
tubing from the pump head.

B.3.5

Installing the Standards Rack

The AS-HV is shipped with an 11-position standards rack (P/N 064253)
(see

Figure B-5

). An optional 6-position standards rack (P/N 064252) is

available, also.

1. Check the rack location mat

for the location of the three
mounting holes that are closest
to the AS-HV chassis. (The
holes may be positioned at the
rear and/or the front of the
mat.)

Figure B-5. Standards Rack (11-position)

Содержание AS-HV



























































































































Результаты поиска

Содержание AS-HV

Отзывы:

Похожие инструкции для AS-HV

Бренды по названию

Популярные бренды

Dionex AS-HV, Руководство оператора

Результаты поиска

Содержание AS-HV

Отзывы:

Похожие инструкции для AS-HV

Бренды по названию

Популярные бренды