Dionex AS-HV Скачать руководство пользователя страница 70

Страница: 70 / 122

AS-HV Operator’s Manual

Doc. 065125-01 10/06

B.3

Installing the AS-HV

B.3.1

Installing the Spill Tray

A spill tray (P/N 064251) is installed in the AS-HV at the factory. If the
spill tray becomes separated from the autosampler during shipping,
follow the procedure below to reinstall the tray.

1. Check that the alignment pins protrude above the base support tube

(see

Figure B-1

2. Position the spill tray so that the two alignment pins at the rear of the

base support tube fit into the slots in the spill tray.

3. Lower the spill tray until the front edge rests on the front of the base

support tube.

4. Verify that the spill tray is secured in place by trying to move it from

side to side; the tray should not move at all.

Figure B-1. Installing the Spill Tray

Base Support
Tube

Spill Tray

(P/N 064251)

Alignment
Pin

Содержание AS-HV



























































































































Результаты поиска

Содержание AS-HV

Отзывы:

Похожие инструкции для AS-HV

Бренды по названию

Популярные бренды

Dionex AS-HV, Руководство оператора

Результаты поиска

Содержание AS-HV

Отзывы:

Похожие инструкции для AS-HV

Бренды по названию

Популярные бренды