DIODE LED EMERY BEAM LED Wet Location Batten Fixture Скачать руководство пользователя страница 3

Страница: 3 / 5

3 OF 5

IG020618-1.0

EMERY

™

BEAM LED Wet Location Batten

INSTALLATION GUIDE

EMERY

™

BEAM LED Wet Location Batten Fixture

INSTALLATION (CONT.)

INSERT EMERY

™

BEAM INTO

MOUNTING BRACKETS

Place mounting channel into brackets one side at a

time.

*Note: If bracket is too tight for mounting channel, use

phillips-head screwdriver to loosen bracket cross screw

until mounting channel is able to fit within bracket.

GROUND (GREEN)

HOT/LINE (BLACK)

NEUTRAL (WHITE)

GROUND (GREEN)

HOT/LINE (BLACK)

NEUTRAL (WHITE)

Use phillips-head screwdriver to tighten bracket cross

screw until fixture is held firmly in place.

3.1

3.2

Connect Green, Black, and White wiring to 120V-277V

AC circuit using twist-on wire connectors. If not using

0-10V dimming, cap purple and gray data wires with

twist-on wire connectors.

ON/OFF

CONNECT WIRING

Содержание EMERY BEAM LED Wet Location Batten Fixture






Результаты поиска

Содержание EMERY BEAM LED Wet Location Batten Fixture

Отзывы:

Похожие инструкции для EMERY BEAM LED Wet Location Batten Fixture

Бренды по названию

Популярные бренды

DIODE LED EMERY BEAM LED Wet Location Batten Fixture, Руководство по установке

Результаты поиска

Содержание EMERY BEAM LED Wet Location Batten Fixture

Отзывы:

Похожие инструкции для EMERY BEAM LED Wet Location Batten Fixture

Бренды по названию

Популярные бренды