Controls
- see
Fig. 3
The product can be controlled both manually and by remote
control.
Manual Controls
Three switches provide a choice of heat setting. A switch is in
the ON position when the side with the markings on is pushed
in..
Switch 1
Controls the electricity supply to the heater.
Note: This switch must be in the ON position for the heater to
operate with or without heat.
Switch 2
Controls the function of the fire.
Press once to the right give flame effect only.
Press again to give heat and flame effect.
Press again to go back to flame effect only.
Pressing the button in the opposite direction at any
stage turns the fire to standby mode.
Switch 3
Controls the heat output from 1kw to 2kw. The 2kw
output is achieved when in
( II )
position.
Note: To turn fire completely off use
Switch 1
.
Thermostat - T
In order to maintain a certain room temperature, set the controller
to ‘max.’. Operate the appliance at full power until the required
room temperature is reached. Set back the thermostatic controller
until the appliance switches off. This temperature will be kept
almost constant by the thermostatic control switching on and off
automatically.Please note that the appliance can only be switched
on when the thermostat setting is higher then the room
temperature.
Initializing the Remote Control
- see
Fig. 4
Note: The remote control is packed separately in the carton.
1. Slide open the battery cover on the back of the remote
transmitter.
2. Install the AAA batteries into the remote control
3. Replace battery cover.
Dispose of batteries in the proper manner according to Provincial
and local regulations. Any battery may leak electrolyte if mixed
with a different battery type, if inserted incorrectly, if all the
batteries are not replaced at the same time, if disposed of in a
fire or if an attempt is made to charge a battery not intended to
be recharged
.
Remote Control Operation
Warning: It takes some time for the receiver to respond to the
transmitter. Do not press the buttons more than once within two
seconds for correct operation. On the control panel, switch
1
must be in the ‘
ON
’ position in order for the PCB to operate.
Setting
Operation
Flame effect
Press ‘
I
’ button once
Flame effect and heat
Press ‘
I
’ button again
By continuously pressing the ‘
I
’ button the fire will cycle between
flame effect and flame effect plus heat.
To turn off any of the settings press the ‘
’ button once.
The remote control may be placed, when not in use, in the wall-
mounted holster provided .
Safety cut-out
For your safety, this appliance has been fitted with thermal cut-
out. In the event that the product overheats, the cut-out switches
the heat off automatically.
To bring the heat back into operation, remove the cause of the
overheating, then unplug or turn off the electrical supply to the
heater for up to 10 minutes.
When the heater has cooled sufficiently, re-connect and switch
on the heater.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Instructions for removing fuel effect
Carefully remove the log effect from the fire by lifting it up and
moving it out. (See
Fig.5)
Disconnect the 9way connector to
completley detach the logset from the fire (See
Fig.6)
.
Lamp Replacement
- see
Fig. 7
Warning – Always disconnect from the power supply before
removing lamps.
The lamps reach high temperatures during operation. For this
reason, allow the lamps to cool down after switching off the
appliance. The lamps are located under the fuel effect
Carefully remove the fuel effect from the fire.The defective lamps
should be replaced with a 60W E14 SES clear candle bulb.
UKRU
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully
with a soft cloth. DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush
attachment of a vacuum cleaner should occasionally be used to
clean the outlet grille of the fan heater.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it
should not be disposed of with household waste.
Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice in your country.
After Sales Service
Your product is guaranteed for one year from the date of
purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided
it has been installed and operated in accordance with these
instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales information or assistance with
this product please go to
www.dimplex.co.uk
where you will
find our self help guide by clicking on “After Sales” or ring our
helpdesk on 0845 600 5444 (UK) or 01 842 4833 (R.O.I.) .
Spare parts are also available on the website
www.dimplex.co.uk
Please retain your receipt as proof of purchase.
Dimplex UK Ltd.
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
www.dimplex.co.uk
Republic of Ireland
Tel.
01 8424833
[c] Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex UK Limited.
