IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions
sho
uld always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the
following:
If the appliance is damaged, check with the supplier
before installation and operation.
Do not use this heater in the immediate surroundings of
a bath, shower or swimming pool.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
Do not cover or obstruct in any way the heat outlet grille
located at the top of the heater or the heat outlet at the
base of the heater. Overheating will result if the heater is
accidentally covered.
The appliance is not intended for use by young children
or
infirm persons unless they have been adequately
supervised by a
responsible person to ensure that they
can use the appliance safely.
Young children should be supervised to ensure that they
do not
play with the appliance.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from the
heater.
Although this heater complies with safety standards, we
do not recommend its use on deep pile carpets or on long
hair type of rugs.
The appliance must be positioned so that the plug is
accessible.
Do not use this heater in series with a thermal control, a
program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists
when the heater is accidentally covered or displaced.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
General
Unpack the heater carefully and retain the packaging for possible
future use, in the event of moving or returning the fire to your
supplier. A remote control and batteries are packed separately
within the carton.
This fire incorporates a flame effect which can be used with or
without heating, so that comforting effect may be enjoyed at any
time of the year. The flame effect is provided by a low wattage
motor and three 60 watt lamps. Using the flame effect on its own,
therefore, requires little electricity.
The controls are located at the bottom right hand corner of the
appliance (see ‘z’ in
Fig. 1
). A choice of 750W or 1500W heat
output is provided by the fan heater, which is concealed at the top
of the heater behind the removable front panel.
The fire is designed to be fitted into a large fireplace opening or a
purpose built structure.
Please note: Used in an environment where background noise is
very low, it may be possible to hear a sound which is related to the
operation of the flame effect. This is normal and should not be a
cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Installation
The fire is designed to be fitted into a large fireplace opening or a
purpose built structure - see
Fig. 1
for dimensions required.
The
installation of a purpose built structure should be carried out by a
competent person. If in doubt please consult your local builder.
At the base of the fire, four adjustable feet (see ‘A’ in
Fig. 1
) are
provided for levelling the fire where the base of the fireplace
opening is raised above the level of the hearth.
Adjust by turning the feet until the desired height has been reached.
Operation
The controls are located at the bottom right hand corner of t
he
appliance - see ‘z’ in
Fig. 1
.
Connect the fire to your electricity supply.
Note:
When either the remote control or the manual controls are
used the neon’s will come on for 3 seconds indicating the
app
ropriate setting - see
Fig. 2
.
Manual Operation
Note:
The Standby Switch (see ‘y’ in
Fig. 4
) must be first turned
on to operate either the manual or the remote controls. The red
indicator mark on the switch will be visible wh
en it is turned on.
Setting
Operation
Indication
Flame effect
Press the ‘
I
’ button once
Bottom Neon
Flame effect & 750W heat setting
Press the ‘
I
’ button again
Middle Neon
Flame effect & 1500W heat setting
Press the ‘
I
’ button again
Top Neon
To turn off any of the settings press the ‘
O
’ button once.
To increase or decrease the brightness of the fuel effect use the
buttons ‘
’ as shown in
Fig. 4
.
Initializing the Remote Control
Note: The remote control is packed separately in the carton.
1.
Slide open the battery cover on the back of the remote
transmitter.
2.
Install the AAA batteries into the remote control.
3.
Replace battery cover.
Dispose of batteries in the proper manner according to Provincial
and local regulations. Any battery may leak electrolyte if mixed
with a different battery type, if inserted incorrectly, if all the batteries
are not replaced at the same time, if disposed of in a fire or if an
attempt is made to charge a battery not intended to be recharged
.
Remote Control
Operation
Warning:
It takes some time for the receiver to respond to the
transmitter. Do not press the buttons more than once within two
seconds for correct operation.
Setting
Operation
Indication
Flame effect
Press the ‘
I
’ button once
Bottom Neon
Flame effect & 750W heat setting
Press the ‘
I
’ button again
Middle Neon
Flame effect & 1500W heat setting
Press the ‘
I
’ button again
Top Neon
To turn off any of the settings press the ‘
O
’ button once.
To increase or decrease the brightness of the fuel effect use the
buttons ‘
’ as shown in
Fig. 3
.
