background image

Remote Operation & Wireless Connectivity

The appliance can be controlled remotely using a smart phone or similar device. To facilitate this remote operation, it 
is necessary to first download the Dimplex 

 app. The App is available on both Android and IOS devices and is 

available free from the Apple or Android App store. The App is compatible with Android version 4.3 and above and 
IOS version 5 and above. 
Once the App has been downloaded it is necessary to pair the appliance with the Smart Phone to complete the 
remote setup. Please follow the steps shown below:

• 

Launch the Dimplex 

 App on the Smart Phone or similar device.

• 

To initiate pairing mode on the appliance press and hold the 

 key for two seconds. The wireless connectivity logo 

 will start flashing. This indicates that the device is advertising to be paired with the App. This is only required for 

initial pairing, for future operation the product will automatically search for a previously connected device and 
connect if available. If an existing device has not been found the appliance will then exit pairing mode and the 
wireless connectivity icon will turn off. 

• 

The smart phone will display appliances available for control. The EvoRad will be identified by a unique 6 digit 
code beginning with 'CV', for example ‘CV7214’ and the ‘Appliance type: C4’. Select this device and press connect 
to initiate pairing.

 Flashing Icon

 Press and Hold

• 

Some phones may require a PIN to be entered to complete pairing, this PIN will be provided on the Smart Phone. 

• 

Once the pairing process is complete the App can be used to control the appliance. 

• 

Once paired successfully the wireless connectivity logo will stop flashing and remain illuminated.

Operational Modes 

The appliance has the following operational modes:

• 

Manual mode,

 this is a continuous active heating mode. It is possible to select a heat output and a desired 

room temperature, the appliance will continue to control the room until the mode is changed or the appliance 
is switched off. 
It is possible to select the heat mode from three available options during the manual mode set up, see '

Heat 

Selection

'

• 

Auto mode,

 this is a scheduled heating mode, the time, heat output and room temperature can be programmed 

for up to four heating periods per day, for each of the seven week days 

• 

Boost mode,

 this is a time limited active heating mode. The appliance will operate continuously for the 

preselected time duration and then revert to Standby mode. There are three options to choose from, 30 
minutes, 1 hour or 2 hours. During a boost period the appliance will operate in Eco heat mode with a default 
set temperature of 25°C. The desired room temperature can be adjusted at any stage during the operational 
period.  At the end of the Boost period the appliance will enter the standby mode.  

Содержание Evo Rad

















Отзывы: