Dimplex DXTT3, Руководство пользователя

Страница: 4 / 4

Installation
The different parts of this appliance used to assemble and mount
this product are identified in Fig. 4. They are the Clamping Knob
- (W), the Saddle - (X), the Foot - (Y) and the Tilt base - (Z).
Note: When mounting the product on its foot for portable use or wall
mounted use it must not be mounted vertically as shown in Fig. 3.
The product is fitted with a safety tilt switch which will prevent it from
operating should the heater be tilted more than 45
o
from horizontal.
Portable Use - see Fig. 1 & Fig. 4
WARNING: The heater should never be used as a portable
appliance without the foot securely fitted.
1. Set the foot (Y) on the ground.
2. Remove both clamping knobs (W) and saddles (X) from the
main heater body by unscrewing the clamping knob (W).
3. Lift the heater, holding it level and horizontal, and line up the
right tilt base (Z) with the corresponding hole in the foot (Y).
4. Line up the clamping knob (W) and saddle (X) with the foot
(Y) and tilt base (Z) and screw the clamping knob (W) into
position until it is tight.
5. Complete the same for the left hand side of the heater.
6. Ensure the heater is stood on a firm level base near to but not
directly beneath a suitable mains supply socket.
7. Maintain the clearances as shown in Fig. 1 to the back and
sides of the heater.
Wall Mounting - see Fig. 2. & Fig. 5
Note: This product weighs approximately 5kg. Supporting wall
structure must be strong and secure.
1. Place the foot (Y) on a suitable wall ensuring it is level and
that the minimum clearance distances detailed in Fig. 2 are
maintained. Ensure that it is not located directly beneath a
mains supply socket.
2. Mark the two mounting hole locations, see Fig. 5, through
the foot (Y).
3. Remove the foot (Y) and prepare the holes for screw fixing.
Solid brick or concrete block walls must be drilled and
plugged.
4. Fix the foot to the wall using suitable screws. (Minimum 60mm
long, mounting holes in foot (Y) are Ø 4.5mm).
5. Complete steps 2 - 5 in portable use section above.
Adjusting the tilt - see Fig. 6
Once the heater is mounted on the foot, the tilt of the heater can
easily be adjusted. Loosen the Clamping knobs on the heater
slightly but do not unscrew completely.
The heater will tilt up 30 degrees from horizontal when portable
and 30 degrees down from horizontal when wall mounted as
shown in Fig. 6.
Using the Heater
Main Elements -
See Fig 7
- Thermostat Knob
- Switch Knob
- Neon
Heat Control
- see Fig. 7
- Off
- Cool Blow*
- Half Heat
- Full Heat
Thermostat Control - see Fig. 7
The heat output is controlled by the thermostat, according to the
room temperature.
Turn the thermostat knob fully clockwise to maximum setting
initially. When the room is warm enough, reduce the setting slowly
until the heater just clicks off.
The heater will now cycle on and off to maintain your selected room
temperature. An audible click may be heard when the thermostat
operates - this is normal.
Note: If the heater does not come on when the thermostat is at a
low setting, this is normally because the room is warmer than the
thermostat setting and is not a fault.
* When the heat control is set to ‘ ’ for cool blow, set the
thermostat control to maximum.
Position ‘ ’ will turn the heater on and off to maintain a temperature
of approximately 5°C.
Safety - overheat protection
For your safety this appliance is fitted with a thermal cut-out. In
the event that the product overheats for some reason, the cut-out
prevents excessive temperatures on the product by cutting the
power to the heater. Once the heater has cooled down, it will reset
automatically, it will continue to cycle on and off automatically until
the reason for overheating is removed.
Fuselink
A thermal fuse link is provided as an added safety feature. If the
fuse link operates and opens circuit it is the result of abnormal
overheating within the appliance and servicing of the appliance by
a competent service engineer will be required in order to ensure
the future safe operation of the heater. Customer services should
be contacted in the event of fault or failure.
Cleaning
WARNING ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powders or polish of
any kind on the heater. Wipe with a dry cloth to remove dust and
a damp cloth (not wet) to clean off stains. Be careful not to allow
moisture into the heater.
Ensure that dust or fluff does not accumulate inside the heater
as this could lead to overheating of the element. Use a vacuum
cleaner to remove any fluff which does accumulate.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it
should not be disposed of with household waste.
Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice
in your country.
After Sales Service and Extended Guarantee
Your product is guaranteed for 1 year from the date of purchase.
The 1 year guarantee is extended for an additional 2 years when
you register the product with Dimplex, within 28 days of purchase.
If you do not register the product with Dimplex within 28 days, your
product will remain guaranteed for 1 year only.
Within the extended guarantee period we undertake to repair or
exchange this product free of charge providing:
a) Proof of purchase such as a sales receipt should be provided,
showing that the appliance was bought within the 36-months
prior to registering the defect/fault.
b) The appliance was correctly installed and operated in
accordance with the manufacturer’s instructions and used solely
for domestic purposes.
c) The defect/fault was not as a result of accident, misuse,
unauthorised modification or inexpert repair
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
To validate your extended guarantee register with us online at
http://register.dimplex.co.uk
N.B. Each qualifying product needs to be registered with Dimplex
individually.
Please note that the extended guarantee is only available in
the UK and Ireland
If after following these steps your product still does not operate
you should return it to your point of purchase.
Please do not return a faulty product to us as this may result in loss
or damage and delay in providing you with a satisfactory service.