Installation
The Fixing Kit should contain: 1 Drilling Template, 3 Screws, 3
Rawlplugs and 1 Mounting Bracket.
Wall Mounted Operation
(see
Fig. 2
)
Suggested Fixings
SOLID BRICK/BLOCK:
No. 8 Rawlplug inserts, 6mm drill bit.
PLASTERBOARD:
If possible locate studding and use No. 8
woodscrews directly into the wood, otherwise M5 rawlplug intersets
are suitable.
NOTE: FOR OTHER WALL TYPES
(e.g. Timber frame and hollow
concrete)
SEEK SPECIALIST ADVICE.
1.
Select the position for the heater ensuring there is
clearance from any furniture and fittings of at least
150mm above the heater, 50mm below, 25mm each
side and 300mm from the front panel. Curtains must
not be closer than 150mm from the top and/or sides of
the heater.
2. Position the drilling template provided on the wall ensuring
it is level. Mark the position of the relevant holes on the
wall at the edge of template. Before drilling check that the
distance between the hole centres is correct, 340mm for
400W Models and 540mm for 800W models (see
Fig. 2
).
Fig. 2
Positioning the Heater
Select the position for the heater ensuring there is clearance
from any furniture and fittings of at least 150mm above the
heater, 50mm below (wall mounted), 25mm each side and
300mm from the front panel. Curtains must not be closer than
150mm from the top and/or sides of the heater.
Free Standing Operation
(see
Fig. 1
)
NEVER USE THE HEATER FREE STANDING WITHOUT THE
FEET FITTED
(FEET ARE PACKED SEPARATELY IN CARTON).
1. Lay the heater on its front.
2. Remove the two star head screws from the base of the
heater using a x-head screwdriver.
3. Place feet over base of heater, align holes and engage hook
on foot into the recess on the back of the heater - see
Fig.
1
.
4. Replace the screws but do not overtighten.
Fig. 1
Rear View
3. Drill the wall at the three marked positions and fit the wall
plugs.
Ensure template has been removed.
4. Fix two No. 8 screws to the top two holes leaving 3mm of
the screw exposed. Hang the heater on the screws.
5. Fit the bottom bracket, found in the fixing kit, in the slot at
the base of the heater and screw the bracket to the wall.
Test that the heater is now securely fixed to the wall.
130mm
340mm - 400W
540mm - 800W
95mm
150mm
50mm
420mm
25mm
25mm
130mm
Drilling Holes
Bracket
Electrical Connection
WARNING THIS APPLIANCE MUST BE EARTHED
If the socket outlets in your home are not of the 13 amp BS1363
type they will not accept the plug connected to this heater,
therefore cut off the plug. When cut off this plug can constitute
a shock hazard if inserted into a socket outlet. It must therefore
be disposed of safely.
Before wiring the appropriate plug please note that the wires in this
mains lead are coloured in accordance with the following code.
GREEN/YELLOW:
EARTH
BLUE: NEUTRAL
BROWN:
LIVE
Connect the
Green/Yellow
wire to the terminal marked
E
or the
earth symbol or coloured
Green
or
Green/Yellow
.
Connect the
Brown
wire to the terminal marked
L
or coloured
Red
.
Connect the
Blue
wire to the terminal marked
N
or coloured
Black
.
DO NOT
connect the
Brown
(
Live
) or the
Blue
(
Neutral
) wires
to the
Earth
terminal of your 13 amp plug. If the terminals of the
plug are unmarked or you are in any doubt, consult a qualified
electrician.
CAUTION:
If you use this heater in conjunction with a thermal
control, programme controller, timer or any other device which
switches the heater on automatically observe all safety warnings
at all times.
Please Note: Although this heater is manufactured to
comply with the relevant safety standards, certain types
of carpets could become discoloured by the temperatures
under a portable heater. If you are concerned about this,
we recommend that you contact the carpet manufacturer
for guidance. Alternatively, either stand the heater on a
suitable base to shield the carpet or wall mount it.
