9
bly to the housing. This will allow you to remove the
heater assembly out of the housing so that you can
access the switches inside. (Figure 6)
Disconnect wiring connections and connect to replace-
12.
ment heater assembly noting their original locations.
Reassemble in the reverse order as above.
13.
POWER CORD REPLACEMENT
Tools Required:
Phillips head Screwdriver
Slip Joint Pliers
Flat Head Screwdriver
WARNINg:
If the fireplace was operating prior to
servicing allow at least 10 minutes for light bulbs and
heating elements to cool off to avoid accidental burning
of skin.
WARNINg:
Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Remove the nut and washer which secure the front trim
1.
to the mantel from behind (Figure 3).
Remove the front trim by pulling it away from the front
2.
of the mantel.
Remove the mesh curtains & rod from the mantel by
3.
pulling them away from the mantel, and set them aside
(Figure 5).
Remove 2 screws from the front of the fireplace which
4.
secure the firebox to the mantel base. These 2 screws
are in the bottom front of the firebox to the left and right
side (Figure 2).
From behind the mantel, remove 11 screws which se-
5.
cure the firebox to the mantel (Figure 3).
Remove the firebox from behind the mantel and lay it
6.
on its back.
Remove the logset and front cover of the firebox by
7.
removing the 4 screws: 2 left and 2 right. They are
located on the lower, side panels of the firebox.
Grasp the rubber gasket connecting the flicker rod and
8.
flicker motor shaft on the right. Simultaneously pull and
twist the gasket (with the flicker rod attached) away
from the motor. Once the rod and gasket are detached,
slide them to the right, guiding the rod out of the left
mounting bracket.
!
NOTE:
When removing the Flicker Rod, damage may
occur if bent excessively or handled improperly. Ensure that
the Flicker Rod is straight and not crushed before reinstall-
ing.
From beneath the firebox, remove the 2 screws that
9.
secure the power cord internal housing to the outer
frame. (Figure 7)
Disconnect wiring connections in the terminal block.
10.
With needle nosed pliers, squeeze and push the grom-
11.
met securing the power cord out of the casing.
Connect the new power cord into the same location.
12.
Reassemble in the reverse order as above.
13.
REMOTE CONTROL RECEIVER
REPLACEMENT
Tools Required:
Phillips head Screwdriver
Slip Joint Pliers
Flat Head Screwdriver
WARNINg:
If the fireplace was operating prior to
servicing allow at least 10 minutes for light bulbs and
heating elements to cool off to avoid accidental burning
of skin.
WARNINg:
Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Remove the nut and washer which secure the front trim
1.
to the mantel from behind (Figure 3).
Remove the front trim by pulling it away from the front
2.
of the mantel.
Remove the mesh curtains & rod from the mantel by
3.
pulling them away from the mantel, and set them aside
(Figure 5).
Remove 2 screws from the front of the fireplace which
4.
secure the firebox to the mantel base. These 2 screws
are in the bottom front of the firebox to the left and right
side (Figure 2).
From behind the mantel, remove 11 screws which se-
5.
cure the firebox to the mantel (Figure 3).
Remove the firebox from behind the mantel and lay it
6.
on its back.
Remove the logset and front cover of the firebox by
7.
removing the 4 screws: 2 left and 2 right. They are
located on the lower, side panels of the firebox.
Remove the lower Partially Reflective Glass retaining
8.
bracket by removing the 2 mounting screws.
Slide the Partially Reflective Glass down and place it
9.
in a safe place. This will give access to the Remote
Control Receiver.
Disconnect the wires noting their original location.
10.
!
NOTE:
A flat head screwdriver can be used to gently
pry between the end of the connector and the receiver to
release the wires.
Remove the original remote control receiver from the
11.
mounting tabs located on the 4 corners of the receiver.
This can be done by cutting the tips of the tabs with
wire snips, or breaking the tips with pliers, then pulling
the receiver off the remainder of the tabs.
Remove the remainder of the original mounting tabs by
12.
pushing them out through the back panel of the fire-
place. Replace with the new mounting tabs provided
with the new remote control receiver into the same
location on the back panel .
Gently push the replacement receiver onto the new
13.
mounting tabs.
Replace the wires into their original configuration.
14.
Re-assemble the fireplace in reverse order.
15.
Содержание CFP4949BW
Страница 6: ...6 www dimplex com WIRING DIAGRAM...
