Portable use
WARNING: THE HEATER SHOULD NEVER BE USED AS A PORTABLE
APPLIANCE WITHOUT THE FEET SECURELY FITTED.
Lay the heater on its back and remove the wall mounting brackets - see
Wall mounting
. Locate and remove the foot fixing screw - see
Fig. 2(a)
.
Clip the foot in place and secure using the foot fixing screw.
NOTE – The wall mounting brackets must be removed before the foot
can be fitted.
Wall Mounting (Installed)
Three identical wall mounting brackets are secured to the base of the heater
with a fixing screw. To wall mount appliance, first remove the brackets as
follows, lay the heater on its back and follow the sequence shown - see
Fig. 3
. Identify and remove the fixing screw securing the brackets located
beside mains cable as shown in (a), pull out brackets and rotate them to
disengage them from the slot and withdraw the brackets from the slot (b).
Select a suitable position, near to a mains power socket whilst ensuring
the minimum mounting clearances are maintained - see
Fig. 1
. Fix the
two top retaining brackets to the wall, using suitable fixings – see
Fig. 4
.
574
Locate the heater on the top brackets and allow it to hang in place.
Fit the bottom bracket into the slot in the heater and then fix it to the wall.
Test that the heater is now securely fixed to the wall.
Controls
Indicator Neon (selected models)
The indicator neon comes on when the appliance is connected to mains
supply.
Thermostat (all models)
The thermostat controls the heat output according to the room temperature.
This ensures that the heater will not produce heat unnecessarily when the
room is warm.
To set the temperature you require, Gradually turn the thermostat knob
clockwise until the desired temperature is reached. Allow some time between
increments for the room temperature to stabilise.
Alternatively to heat a cold room quickly, turn the thermostat knob to the
Max position. When the room has reached the desired temperature, turn
the thermostat knob anti-clockwise until the thermostat clicks off. The heater
will then automatically maintain this room temperature.
The thermostat also has a frost protection setting marked ‘ ’. This setting is
useful in areas such as garages to prevent frost damage. If the thermostat is
set to its minimum setting ‘ ’, the heater will cycle ON and OFF to maintain
a temperature of approximately 5°C to help protect against frosty conditions.
Switches (selected models)
Selected models are supplied with selector switches . There are two switch
types, one is an on/off switch and the other is a heat selection switch.
Depending on model either one or both switch may be included. The switch
operation is as follows.
On/Off:
O
- Off
I
- On
Heat selection
I
-
Low heat
II
-
High heat
Mechanical Timer
(selected models)
Note: The timer clock will only operate when the product is connected to
the mains supply
Operation modes
There are two operating modes on the timer, Manual operation and Auto
operation. The operation mode is set using the slide switch on the timer
- see
fig 6.
Manual operation
(Position - I)
This setting allows power to the product uninterrupted by the timer,
however other product controls will continue to function as normal.
Auto operation
(Position - )
This setting allows the heater to be controlled by the timer. The
product will be switched on and off depending on the pre-set timer
program.
Setting the time of day
To set the time of day, rotate the timer dial clockwise (indicated by the
arrow) until the correct time of day is opposite the reference mark -
see
Fig. 6
. The 24-hour clock is used ; e.g. 4 pm is ‘16’ (16:00hrs)
.
Setting the ‘Auto’ ON and OFF times
To set the timer :
1.
Using your finger tip or the tip of a pencil, push in as many
segments as necessary around the dial, according to the times you
don’t require heat – see
Fig. 7
. Each segment pushed in switches
the heater OFF for that part of the hour. All other segments will be
ON. For example,
Fig. 7
shows the timer set to switch the heater
OFF between 11pm and 1.45am.
2.
You can select as many ON periods
as you like, within the 24-hour
day. The settings will repeat every day until changed.
3.
To change ON and OFF times, simply push in any ‘ON’ segments
you wish to cancel and pull out new ‘ON’ segments as required.
Fig. 6
Fig. 4
Fig. 5
Fig. 3
Fig. 2
