Dilog DL9110 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 37

background image

DL9110 / DL9118

Operating Instructions

- 31 -

7 Environmental Conditions

The  DL9110  /  DL9118  has  been  designed  to  perform  tests  and
measurements in a dry environment.

Maximum barometric elevation for making measurements is 2000M.

Overvoltage category IEC 60664/IEC 61010, 300V Category III.

Pollution degree 2 according to IEC 61010-1.

Protective system IP40 according to IEC 60529.

Electromagnetic  compatibility  (EMC).  Interference  immunity  and
emitted interference conforming to IEC 61326-1.

Operating  temperature  range  of  0°C  to  40°C,  without  moisture
condensation.

The DL9110 / DL9118 can be stored at any temperature in the range -
25°C  to  +65°C  (relative  humidity  up  to  90%).  The  batteries  should  be
taken out of the instrument for storage.

Operating Altitude 0 to 2000 metres

«
...
29
30
31
32
33
...
»

Содержание DL9110






































Отзывы:

Нет отзывов

Похожие инструкции для DL9110

Бренд: Rain Bird Страницы: 2

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Haigh Страницы: 60

Бренд: Backyard Discovery Страницы: 79

Бренд: Badger Meter Страницы: 16

Бренд: Cadman Страницы: 84

Бренд: Garmin Страницы: 20

Бренд: Uchida Yoko Страницы: 40

Бренд: EFX Страницы: 2

Бренд: Ebyte Страницы: 7

Бренд: Sabo Страницы: 76

Бренд: Zafferano Страницы: 28

Бренд: Basler Страницы: 33

DynaTrap DT1260-TUN

Бренд: Dynamic Страницы: 4

Бренд: Elma Страницы: 35

Бренд: Qtx Страницы: 6

Бренд: Parkside Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды