manualshive.com logo in svg

Digitronic CamCon DC30, Руководство пользователя, Страница: 18 / 24

Поделиться
Скачать
Digitronic CamCon DC30 Скачать руководство пользователя страница 18

Digital Cam Switch Unit

Digitronic

CamCon DC30

Automationsanlagen GmbH

6.3.7.3. Deletion of a particular cam

Task:

The cam from 300 to 330 on output 2 shall be deleted.

Solution:

1.

Press the

key (for about 2 sec.), you enter the 'Output selection' mode

.

2.

Press the

key to select output 2,

. The start of the first cam found is displayed.

3.

Press the

key, you enter the 'Cam search' mode

.

4.

Press the

key, the device searches for the start of the next cam.

is displayed.

5.

Press the

key. The preselection

is displayed.

6.

Press the

key to program the activation point. The display shows

.

7.

Press the

key and keep it pressed until the display shows

.

CAUTION!

Do not keep the key pressed too long. It is best to keep the

key pressed until 320

and then adjust to 330 step by step.

8.

Press the

key. You return to the standard display.

NOTE:

By shifting the cam activation point to the cam deactivation point the programmed cam is deleted. By
shifting  the  activation  point  beyond  the  deactivation  point  deletes  the  range  after  the  cam  (e.g.  from
330 to 350). All cams programmed in this range are deleted. A new cam will be placed between 330
and 350 when you move the activation point back to the desired position of 330 !

Page: 18

Version from: 04.06.2002

Содержание CamCon DC30

























Отзывы:

Нет отзывов