DigiTech PDS3500 Скачать руководство пользователя страница 6

Страница: 6 / 21

gram change number, (2) a MIDI channel number, and (3) a pedal status number. The pedal status

number assigns the function of the FX-17 to one of the defined MIDI continuous controllers, pitch bend,

or channel pressure.

Apply power to the PDS-3500 with the switches in the OPERATE and BANK/PRESET positions. If

the LED display does not read "10," remove and re-apply power to the unit.

The PDS-3500 has two operating modes, the BANK/PRESET mode or the BANK DUMP mode.

As you increment through the BANK numbers, the PRESET number shown on the LED display is

"0." This is a null preset that does not transmit any data, but acts as a starting point for either of the two

operating modes.

The BANK/PRESET MODE allows you to step through the presets in each bank one at a time, the

left foot switch selecting the bank number and the right foot switch selecting the preset number. When

the right foot switch is depressed, the PRESET NUMBER is advanced by one, the MIDI PROGRAM

CHANGE number stored in memory for that preset is displayed momentarily and the preset data is

transmitted.

The BANK DUMP MODE sends out all of the presets in the selected bank. This mode allows you to

set up many different effects units with different corresponding MIDI program numbers with one tap of

your foot. You can assign each effect device to listen on a different MIDI channel, then in each preset in

order, program a different MIDI program number for each MIDI channel (the continuous controller

definition being the last preset). Put the left hand switch in the OPERATE mode and the right hand

switch in the BANK DUMP mode, select the BANK number with the left (BANK/STORE) foot switch.

Only when you depress the right (PRESET/ INCREMENT) foot switch are all of the presets in the bank

transmitted in the order of the preset numbers. The LED display will show "...." while all of the presets in

the bank are being transmitted.

Programming the PDS-3500 .is straightforward. With the use of the left and right three-position

switches and the two foot switches, the BANK number, the PRESET number, the MIDI PROGRAM num-

ber, the MIDI CHANNEL number, and the PEDAL STATUS number are quickly programmed into THE

MIDI PEDAL. The programmed settings are stored until changed and are backed up by a battery when

power is removed from the unit.

The first step in programming the PDS-3500 is to determine what you wish to put into the unit. The

Содержание PDS3500






















Результаты поиска

Содержание PDS3500

Отзывы:

DigiTech PDS3500, Руководство пользователя, Страница: 6 / 21

Результаты поиска

Содержание PDS3500

Отзывы: