Digisol DG-GS4200 Series Скачать руководство пользователя страница 12

                                                                             

DG-GS4200 Installation Guide

 

 

 

2-4 

 

and  cables/lines  (power  cables,  signal  lines,  and  output  lines).  The  following  should  be 

noted:   

 

Precautions should be taken to prevent power source interruptions;   

 

Provide  the  system  with  a  dedicated  grounding,  rather  than  sharing  the  grounding 

with the electronic equipment or lightning protection devices.   

 

Keep away from high power radio transmitters, radar transmitters, and high frequency 

strong circuit devices.   

 

Provide electromagnetic shielding if necessary. 

2.1.1.6 Rack Configuration 

The  dimension  of  the  switch  is 

designed  to  be  mounted  on  a  standard  19’’  rack. 

Please ensure good ventilation for the rack. 

 

Every device in the rack will generate heat during operation, therefore vent and fans 

must be provided for an enclosed rack, and devices should not be stacked closely. 

 

When mounting  devices  in  an  open  rack,  care  should be  taken  to prevent  the  rack 

frame  from  obstructing  the  switch  ventilation  openings.  Be  sure  to  check  the 

positioning of the switch after installation to avoid the aforementioned. 

 

Caution

 

If  a  standard  19’’  rack  is  not  available,  the  switch  can  be  placed  on  a  clean  level 

desktop, leave a clearance of 10mm around the switch for ventilation, and do not place 

anything on top of the switch. 

2.1.2 Installation Notice 

 

Read  through  the  installation  instruction  carefully  before  operating  on  the  system. 

Make  sure  the  installation  materials  and  tools  are  prepared.  And  make  sure  the 

installation site is well prepared. 

 

During  the  installation,  users  must  use  the  brackets  and  screws  provided  in  the 

accessory  kit.  Users  should  use  the  proper  tools  to  perform  the  installation.  Users 

should  always  wear  antistatic  uniform  and  ESD  wrist  straps.  Users  should  use 

standard cables and connecters.   

 

After  the  installation,  users  should  clean  the  site.  Before  powering  on  the  switch, 

users should ensure the switch is well grounded. Users should maintain the switch 

regularly to extend the lifespan of the switch. 

Содержание DG-GS4200 Series




















Отзывы: