Digimerge DPD23D Скачать руководство пользователя страница 5

Страница: 5 / 14

-5-

-4-

JUNCTION BOX INSTALLATION TYPES

VANDAL DOME FITTINGS

2S FITTING

a. 2S Fitting requires only 2pcs of base

attachment screws.

Note: You have a reduced space in which

to hide cables using this type of

installation. Recommended for indoor

dome only.

Pendant Cap - model # MNTV2XPC

Replaces the need for the camera base.

Compatible with ceiling conduit installations

Pole Mount - model # MNTV2XP

Junction Box Accessory - model # MNTV2XJ

Fits either wall mount and corner mount bracket.

Symmetrical so reversible for top or bottom

conduit.

Corner Mount bracket - model # MNTV2XR

Can fit either Wall Bracket or Junction Box.

Pendant Mount - model # MNTV2XC

TWO GANG FITTING

a. Two gang fitting (switch box) requires 4pcs

of base attachment screws.

Note: A two gang provides the most robust

fitting. Suitable for both indoor and

vandal domes.

4S FITTING

a. 4S Fitting requires 2pcs of base attachment

screws.

Note: Screws used for the 4S box are larger

compared to those used for the 2S (M4

type). Suitable for both indoor and

vandal domes

OCTAGON FITTING

a. 4” Octagon fitting requires only 2pcs of

base attachment screws.

Note Screws used for the octagon fitting

are larger compared to those used for

the 2S/4S (M4 type). Suitable for both

indoor and vandal domes

Cable

Entry

Screws

Cable

Entry

Screws

Cable

Entry

Screws

Cable

Entry

Screws

Wall Mount - model # MNTV2XW

Содержание DPD23D















Результаты поиска

Содержание DPD23D

Отзывы:

Бренды по названию

Популярные бренды

Digimerge DPD23D, Инструкция по эксплуатации

Результаты поиска

Содержание DPD23D

Отзывы:

Бренды по названию

Популярные бренды