background image

WebColour - Web Based LED Control 

User Manual 

7.0 - 23 November 2020 

 

 

digilin.com.au 

Page 8 of 25 

+617 3899 1267 

 

Toggling Power 

To turn the LEDs controlled by the WebColour off, simply 

press the power button.   

 

To turn the LEDs controlled by the WebColour on, press 

either the power button or the show button. 

Selecting a Static Colour 

To select a static colour 

1.

 

Bring up the show page by clicking on the Show 

Button 

2.

 

Use the left/right arrows if necessary so that the 

current show type displays Static Colour. 

3.

 

Click a position on the Colour Selection Palette.  

Note that the Show Button will change colour to 

match the selected point.  It is also possible to 

click and drag across the Colour Selection Palette 

to select the desired colour. 

Selecting a Show 

To select a show 

1.

 

Bring up the show page by clicking on the Show 

Button 

2.

 

Use the left/right arrows if necessary so that the 

current show type displays the desired show type 

(either Subtle, Dynamic or Smart). 

3.

 

Use the lower set of left/right arrows to select the 

desired show.  The descriptor for each show 

includes 

a.

 

The show number 

b.

 

A brief description of the show 

c.

 

Length of the show in the format h:mm:ss 

followed by the hold time on each colour 

(if applicable). 

 

Details of the colour sequence of each show are listed later 

in this manual. 

Dimming 

There are 3 dimmers visible on all of the colour or show 

select screens as shown on Figure 3. 

Master Dimmer 

The master dimmer will dim all active channels from 10 to 100% in 10% steps.  If RGBW mode is enabled, the 

master dimmer will dim the level set by the RGB and white dimmers (meaning it is possible to dim down to 

1%). 

 

To set a level, either click at the desired point on the bar, or click and drag the slider. 

 

Figure 4. The user interface showing Static 

Colour Selection in RGB mode.

 

Figure 5 The user interface showing Show 

Selection in RGB mode.

 

Содержание WebColour


























Отзывы: