background image

WR44 Series Installation Guide 

Special notes on safety for wireless routers. 

Digi  International  products  are  designed  to  the  highest  standards  of  safety  and 
international standards compliance for the markets in which they are sold. However, GSM 
based  products  contain  radio  devices  which  require  specific  consideration.  Please  take 
the  time  to  read  and  understand  the  following  guidance.  Digi  International  assumes  no 
liability for an end user‟s failure to comply with these precautions. 

 

Wireless  routers  incorporate  a  wireless  radio  module.  Users  should 
ensure that the antenna(s) is (are) positioned at least 1 metre away from 
themselves and other persons in normal operation. 

When in a hospital or other health care facility, observe the restrictions on 
the  use  of  mobile  phones.  Do  not  use  the  router  in  areas  where 
guidelines  posted  in  sensitive  areas  instruct  users  to  switch  off  mobile 
phones. Medical equipment may be sensitive to RF energy. 

The  operation  of  cardiac  pacemakers,  other  implanted  medical 
equipment and hearing aids can be affected by interference from cellular 
terminals such as the wireless routers when placed close to the device. If 
in  doubt  about  potential  danger,  contact  the  physician  or  the 
manufacturer  of  the  device  to  verify  that  the  equipment  is  properly 
shielded.  Pacemaker  patients  are  advised  to  keep  the  wireless  router 
away from the pacemaker while it is on. 

 

Wireless  routers  must  NOT  be  operated  on  aircraft.  The  operation  of 
wireless appliances in an aircraft is forbidden to prevent interference with 
communications systems. Failure to observe these instructions may lead 
to  the  suspension  or  denial  of  cellular  services  to  the  offender,  legal 
action, or both. 

 

As  with  any  electrical  equipment,  you  should  not  operate  your  wireless 
router in the presence of flammable gases, fumes or potentially explosive 
atmospheres.  Radio  devices  should  not  be  used  anywhere  that  blasting 
operations are taking place. 

 

Wireless  routers  receive  and  transmit  radio  frequency  energy  while 
switched on. Remember that interference can  occur if it is used close to 
TV  sets,  radios,  computers  or  inadequately  shielded  equipment.  Follow 
any  special  regulations  and  always  switch  off  your  wireless  router 
wherever  forbidden  or  when  you  suspect  that  it  may  cause  interference 
or danger. 

 

SOS  IMPORTANT! 

–  Wireless  routers  operate  using  radio  signals  and 

cellular  networks  cannot  be  guaranteed  to  connect  in  all  possible 
conditions.  Therefore,  you  should  never  rely  solely  upon  any  wireless 
device for life critical communications. 

 

Содержание TransPort WR44





















Отзывы: