Accessing the CD from a UNIX System
Software &
Documentation
Insert CD in system CD drive
Mount the CD by entering one of the commands from
the following table:
1
2
3
4
Determine your CD device
Common names for CD-ROM devices:
NAME
EXAMPLE
/dev/cdrom
/dev/cdrom
/dev/cdrom/cdrom
n
/dev/cdrom/cdrom1
/dev/cd
n
/dev/cd0
/dev/dsk/c
k
t
m
d
n
/dev/c1t2d0
If your system auto mounts the CD, skip to step 5.
Auto Mount programs may use the volume information
to define a mount point. If the CD volume label is "Digi"
then the mount point may be /cdrom/digi
AIX
*HPUX
SCO
UnixWare
SCO
OpenServer
Solaris
(Intel &
SPARC)
Command
mount -r -v cdrfs
device mount-directory
do not use mount, it will not operate correctly
pfs_mount
device mount-directory
See man pages for
pfs
and
pfs_mount
for more
information.
mount -r -F cdfs
device mount-directory
mount -r -f ISO9660
device mount-directory
mount -F hsfs
device mount-directory
Most systems use an auto-mounter. See the man page
on vold:
man vold
Operating
System
device
is the path to the device file assigned to the cdrom drive,
mount-directory
is the directory where the Digi CD is mounted
Navigate to mounted CD directory, enter:
./setup
5
UNIX
To list descriptions of devices:
AIX:
lscfg
HPUX: - Make sure you have administrator privileges and
your PATH includes /usr/sbin
ioscan -funC disk
Solaris: Most Solaris systems use an auto-mounter.
See the man page on vold:
man vold
If you see DISPLAY permission errors when running the
CD, you may want to verify your DISPLAY variable is set.
To set the DISPLAY variable:
DISPLAY=localhost:0.0; export DISPLAY
AND/OR
xhost +localhost
Identify the mount-directory.
Some common pre-existing mount points:
/mnt/cdrom /cdrom
Or create your own:
mkdir /mnt/mycdrom
HPUX - Check to see if pfs is running
ps -ef | grep pfs
If not, start the daemons:
pfs_mountd&; pfsd&
*HPUX When finished, leave the CD directory and pfs_umount
cd
pfs_umount
mount-directory
(If you inadvertenly use
umount
instead of
pfs_umount
, kill the
pfs daemons to remove the CD-ROM.)
All RJ-45 cables and connectors are 8-pin. When using these adapters with modems or other applications that require
DCD on pin 1, you must turn on altpin. If altpin is turned off, the hardware signal on pin 1 becomes DSR instead of
DCD. This alternative can be used if DCD is not required, and DSR is needed instead. Configure the altpin through
the web interface or the command line. See the User's Guide, MEI chapter or the set flow command in the Command
Reference on the Digi CD under Documentation for more information about setting the altpin.
Cabling your serial devices to a
Digi Product is now simpler than ever
with a Digi Cable Adapter. While many
custom cabling solutions can leave you
with a cable that is either too long or too
short for your application, the
Digi Cable Adapters are used with
commercially available CAT 5 cable of
any length. Simply plug standard CAT 5
cable into your Digi Product, connect a
Cable Adapter to the other end and plug
the adapter into your device. Whether
you need a crossover or straight-through
connection, or require a DB-9 or
DB-25 connector, there is a
Digi Cable Adapter solution.
For additional cabling information, see the
Cabling guide under Documentation on
your CD. If you prefer to order cables,
see our website at http://support.digi.com
and select Cabling.
Digi TS EIA-232 Cable Adapter Reference
Bay Accelar, Nortel and other DB-9 DTE devices
Sun Sparc, Sun Ultra, terminals, printers and other
DTE devices with DB-25 Female ports
Cisco, IBM and other DTE devices with
DB-25 Male ports
Modems and other DCE devices with
DB-25 Female Ports
Modems and other DCE devices with
DB-9 Female Ports
For use with Printers. This adapter differs
from a Console Adapter in that it utilizes the
DTR signal (instead of RTS) for hardware flow control
For use with Cisco and Sun RJ-45 Console ports.
Also available in 8-pack and 16-pack quantities.
Can be used as a networking cable or combined with
one of the adapters as a serial cable.
76000697 Digi TS DB-9F
Console Adapter (4-pack)
76000698 Digi TS DB-25M
Console Adapter (4-pack)
76000699 Digi TS DB-25F
Console Adapter (4-pack)
76000700 Digi TS DB-25M
Modem Adapter (4-pack)
76000701 Digi TS DB-9M
Modem Adapter (4-pack)
76000692 Digi TS DB-25M
Printer Adapter (4-pack)
76000631 Digi TS to
Sun Netra / Cisco Cable
(single pack)
63000042-01 RJ-45 to RJ-45
Straight Through
Ethernet Cable
Part number
Application
Adapter
Need help with cabling?
Linux
mount
device mount-directory
RI
TXD-
TXD-
DSR
RxD-
RxD-
RTS
RTS+
n/a
GND
GND
GND
TxD
TxD+
TxD+
RxD
RxD+
RxD+
SG
SG
SG
CTS
CTS+
n/a
n/a
n/a
DTR
RTS-
DCD
CTS-
Pinouts
RJ-45
Pin
EIA-232
EIA-422/485
Full-Duplex
EIA-485
Half-Duplex
Pin 1
