Digi MIL-4511H Скачать руководство пользователя страница 12

 

Doc. Number: 75424   Rev. A

 

L e g a l

 

R e g u l a t o r y   A p p rova l s

 

FCC Class A

UL 1950

CSA 22 No. 950

EN60950

CE 
– EN55022 Class B
– EN50082-1

 

C a n a d i a n   E M I   N o t i c e

 

This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing 
Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel 
brouilleur du Canada.

 

E u ro p e a n   N o t i c e

 

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage 
Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these 
directives implies conformity to the following European Norms:

EN55022 (CISPR 22) - Radio Frequency Interference

EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity

EN60950 (IEC950) - Product Safety

 

To   C o n t a c t   D i g i

 

For prompt response when calling for service information, have the following information ready:

Product serial number and rev.

Date of purchase

Vendor or place of purchase

Reach Digi Technical Support at 408/744-2751
Or E-mail at “[email protected]

 

Address: 1299 Orleans Drive

Sunnyvale, CA 94089

Voice:

408/744-2775 

Fax:

408/744-2793 

E-mail:

[email protected]

Five-Year Limited Warranty

Digi International warrants to the original consumer or purchaser that each of its 
products, and all components thereof, will be free from defects in material and/or 
workmanship for a period of five years from the original factory shipment date. Any 
warranty hereunder is extended to the original consumer or purchaser and is not 
assignable.

Digi makes no express or implied warranties including, but not limited to, any implied 
warranty of merchantability or fitness for a particular purpose, except as expressly set 
forth in this warranty. In no event shall Digi be liable for incidental or consequential 
damages, costs, or expenses arising out of or in connection with the performance of the 
product delivered hereunder. Digi will in no case cover damages arising out of the 
product being used in a negligent fashion or manner.

Содержание MIL-4511H













Отзывы: