digades dguard Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 10

digades dguard Скачать руководство пользователя страница 8

Installation:

1. Select the hose clip that matches the diameter of your steering rod and pull the shrink sleeve with the

required length over the hose clip.

  2. Use a heat gun to shrink the shrink sleeve back.
  3. Guide the hose clip through the openings on the handlebar adapter.
  4. Ensure that the cable with the 3-pin connection is long enough to reach the installation location on the

steering rod and that your steering movements are not impaired.

  5. Ensure that the recess of the handlebar adapter is seated on the steering rod.
  6. Fix the hose clip with the handlebar adapter to the steering rod and tighten it with a screwdriver.
  7. Thoroughly clean the handlebar adapter and the dguard

®

button for the adhesive pad and remove all

residue of dust, moisture or grease.

8. Ensure that the adhesive surface of the adhesive pad is free of contamination.
9. Stick the adhesive pad to the handlebar adapter.
10.Press the dguard

®

button against the adhesive surface on the handlebar adapter.

11.Connect the cable with the 3-pin connection to the dguard

®

button.

installation dguard

®

installation - dguard

®

button:

«
...
6
7
8
9
10
»

Содержание dguard











Отзывы:

Нет отзывов