manualshive.com logo in svg

Diamond SmartLyte Plus, Руководство по обслуживанию

Поделиться
Скачать
Diamond SmartLyte Plus Скачать руководство пользователя страница 26

1 Introduction

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 26 of 58 

 

1.3.1.7. Electrode Tray Assembly  

This assembly is comprised of the electrode tray and the sample sensor, AV-BP5036D.  (

Figure 

1-31

) 

 

Figure 1-31 Electrode Tray with Sample Sensor 

To remove the electrode tray assembly from the analyzer; 

1.  First, if the instrument is on, place in Hold in Maintenance mode to prevent reagents from 

cycling. (

Main Operations Menu>>>Maintenance>>>Hold in Maintenance

) 

2.  Disconnect the sample sensor cable from the analyzer. (

Figure 1-31

)  

3.  Remove the sample intake tubing on the right side of the assembly where the sample sensor 

is located. (

Figure 1-31

)  

 

Figure 1-32 Electrode Tray with electrodes installed 

4.  Unplug the Reference Tubing Connector  

5.  Disconnect the waste tube (green tag) from the left side of the electrode tray.  

6.  Use one hand to press the Electrode Tray Plastic Tabs toward the center. 

Sample Sensor 

Electrode Tray 

Base 

Sample Intake 

Tubing 

Sample Sensor 

Connector 

Reference Tubing 

Connector 

Waste Tube 

(tagged Green) 

Содержание SmartLyte Plus



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды