Diamond HEX HA 700.2 Скачать руководство пользователя страница 10

10

Installing the Remote Level Controller 

The HA 750.1 comes packaged with a remote level control. This allows you to control the level 

by attenuating the amplitude or increasing (up to the maximum set-point) of the amplifier’s 

input gain control. This control does not add additional gain, it simply allows you to control 

the level to suit your tastes. 

1)

  Locate a position in the front of the vehicle where this will be easy to reach. Common 

locations are on, in, or under the dash, in the center console, or in the glove box. 

2)

  To mount the unit, attach the bracket using the supplied hardware to your chosen loca-

tion. 

3)

   Route the telephone style data cable back to the amplifier location and connect into the 

remote level port. Test to make sure the operation is functioning.

Get Ready to Listen!

Perform a final check of the completed system wiring to ensure that all connections are 

accurate. Check all power and ground connections for frayed wires and loose connections 

which could cause problems. Install in-line fuse near battery connection at this time. Prepare 

to make some adjustments to fine tune your audio system for optimum performance.

Adjustment of Input Gain
To  adjust  the  gain  setting,  turn  the  amplifier  gains  all  the  way  down  (counterclockwise). 

Turn the source unit volume up until distortion is audible and then turn it down a bit until 

the distortion is inaudible. This will be NEARLY full volume on most source units, perhaps 

one or two “clicks” down from maximum volume. Next, increase the amplifier gain setting 

until adequate volume is achieved. 

NOTE:

  Ideal signal to noise and dynamic range are achieved with the gain at minimum. Most 

users find adequate gain and volume is achieved at about halfway in the adjustment range. 

Avoid setting the amplifier gain very high as noise and distortion will increase significantly. 

For a more in depth level setting (gain adjustment) procedure, visit the DAT website at www.

diamondaudio.com

         

EVgVaaZa8dccZXi^dc

HZg^Zh8dccZXi^dc

For more wiring options, see the Support section at www.diamondaudio.com

Содержание HEX HA 700.2













Отзывы: