Diamond FVS-711/TS Скачать руководство пользователя страница 21

Страница: 21 / 25

Description

Code A090

The temperature inside electronic components compartment (on the right hand

side of the oven) is too high and can damage the integrity of the components.

Oven functioning

If the oven is cooking, it stops.

It’s not possible to keep on using the oven.

Resetting

The oven will be operative again, when the temperature will be lower than the

selected value.

Suggestions for the operator

Check the ventilation holes under the control panel (next to USB and core probe

connector) are not obstructed. Check the ventilation holes on the right hand side

panel are not obstructed and that the air can pass through these holes.

If the problem persists, call the technical service.

Remarks for the technical service

Check the functioning and the connections of the cooling fan for the components compartment.

Ensure there are not hot sources next to the right hand side of the oven (we recommend a minimum distance

of 50 cm). Check the ventilation holes are not obstructed by grease or dust.

7.2 NOT SERIOUS ALARMS

Description

Code A210

The core probe doesn’t work properly.

It’s not possible to use this device.

Oven functioning

It’s possible to use the oven with time control of the cooking.

It’s not possible to use automatic programs including one or more phases con-

trolled by the core probe.

Resetting

The oven can work with core probe again, when the core probe is functioning

correctly again.

Suggestions for the operator

Check the core probe is properly connected to the oven.

Check the cable and the skewer are integral

If the problem persists call the technical service.

Remarks for the technical service

Check the functioning of the core probe (the reading of the heating element in ohm of the probe must be 1000

+ room temperature). If necessary, replace the core probe.

ATTENTION!

HIGH TEMPERATURE

ELECTRONIC DEVICES

COMPARTMENT

SWITCH OFF THE OVEN

IF AFTER ONE HOUR

THE MALFUNCTIONING

DOESN’T DISAPPEAR

CALL TECHNICAL SERVICE

ATTENTION!

CORE PROBE

MALFUNCTIONING

DISCONNECT CORE

PROBE

IT IS POSSIBLE TO KEEP

COOKING ONLY USING

TIME CONTROL

REPLACE CORE PROBE

Содержание FVS-711/TS


























Результаты поиска

Содержание FVS-711/TS

Отзывы:

Бренды по названию

Популярные бренды

Diamond FVS-711/TS, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FVS-711/TS

Отзывы:

Бренды по названию

Популярные бренды