background image

27

VI. MAINTENANCE

1. MAINTENENCE

All the components requiring maintenance are accessible
from the front of the appliance, after removing the control
panel and front panel. Disconnect the power supply before
opening the appliance

1.1 BRIEF TROUBLESHOOTING GUIDE

Even in normal appliance operating conditions, malfunctions
can occasionally occur.

-

The pilot burner of open burners does not light

Possible causes:

Insufficient pressure in gas pipes.

Nozzle blocked.

Faulty gas cock.

-

The oven pilot burner does not light

Possible causes:

Igniter not properly fixed or connected

The piezoelectric ignition or igniter cable are damaged.

Insufficient pressure in gas pipes

Worn nozzle

Faulty gas valve

-

The pilot burner goes out when the “pilot ignition” knob is
released

Possible causes:

The pilot bur ner is not heating the thermocouple
sufficiently.

Faulty thermocouple.

The gas cock and/or gas valve knob is not being pressed
enough.

Lack of gas pressure to the cock and/or valve.

Faulty gas cock or gas valve.

-

The pilot burner is still lit but the main burner does not light

Possible causes:

Loss of pressure in gas supply pipe.

Blocked nozzle or faulty gas cock or valve.

Gas outlet holes on burner clogged.

-

The oven temperature cannot be adjusted.

Possible causes:

Faulty thermostat bulb.

Faulty gas valve.

Faulty electric thermostat.

Electric safety thermostat tripped.

ABNORMAL OPERATION

Any of the following are considered to be abnormal operation

and may require servicing:

incomplete ignition of the burner;

yellow tipping of the burner flame;

burner failing to remain alight;

gas valves are difficult to turn;

burner exitinguished by operation of oven door.

In case the appliance fails to operate correctly, contact the

authorised service provider in your area.

INSTRUCTIONS FOR REPLACING COMPONENTS (to be
carried out only by an authorised installer).

Remove the front panel to access:

GAS COCK

Unscrew the pilot and thermocouple pipe, unscrew the
gas inlet and outlet connections.

For installation carry out the same procedure in reverse order.

PILOT BURNER, THERMOCOUPLE, IGNITER ASSEMBLY

To replace the igniter and thermocouple loosen the fixing
screws and remove the components.

To replace the pilot burner undo the gas pipe, remove the
pilot burner assembly

Replace the components, proceeding in reverse order to
refit the parts.

MAIN BURNER

Unscrew the gas connection from the nozzle holder

Undo the screws fixing the burner to the support

Remove the pilot burner assembly by undoing the screws

For installation carry out the same procedure in reverse order,
making sure that when positioning the burner the centering
pins, located at the back of the burner, enter their special seats

1.2 MAINTENENCE SCHEDULE

It is reccommended the appliance is inspected and
serviced by an authorized person at least every 12
months. For this purpose it is reccommended to draw up
a maintenece contract.

AUSTRALIA
For service and spare parts, please contact:

Electrolux - Tom Staddart Pty Ltd
Zanussi - JL Lennard Pty Ltd

Содержание 373000














Отзывы: