background image

C. Water Systems

The

PRECISION 2000™

 comes equipped with brass water supply nozzle and large capacity water bottle, offering better 

water

 ow to the front of the blade for increased cooling and lubrication.

1) Remove water bottle cap and 

 ll with approximately 24 oz. of water. Replace cap but do not screw lid on 

    tightly. A moderately loose lid will prevent a vacuum from occurring. 

2) When ready to cut, open water valve on the bottom of the bottle by pushing the lever downward (Fig.7). Water 

    should begin to 

 ow freely from the water nozzle mounted on the blade guide assembly.  Water nozzle is factory set 

    to 

 ow on the front of the blade. However, some movement may have occurred during shipment. To adjust position 

    of the nozzle, loosen the hex screw on the side of the blade guide assembly (Fig.8) and adjust the brass nozzle into 

    proper position so the water 

 ows to the front of the blade, retighten screw. 

3) The water should drain off the work surface, through the 2 holes on the left side of the table, draining into the 

    lower wheel cover which acts as a reservoir. 

4) The 

PRECISION 2000™

 is equipped with a large drainage spout at the base of the saw (Fig.9). Connect tubing to 

    this spout and secure with locking clip. Place the open end of tube into a collection tray, bucket or sink.  

WARNING: When using a Diamond Blade, never operate saw if there is insuf

 cient water at the point of cutting, as this 

will cause damage to the blade.

USE AND MAINTENANCE

A.  Blade Guide Adjustment

The

PRECISION 2000™ 

comes with lower and upper blade guides. Correct alignment of these guides is essential to 

proper glass cutting and extending blade life.

1) The blade should pass through the grooves of the upper and lower blade guides with the back edge of the blade 

         resting slightly inside the grooves. To adjust, use a small hex wrench and loosen the set screw located on the 

         right side of the lower (Fig.10) or upper blade guide assembly (Fig.11). Slide the blade guide back or forward to 

         achieve proper positioning. The blade should pass vertically through the guides when viewed from the side. The 

PRECISION 2000™

  blade guides can be rotated 3 times for extended guide wear.

NOTE: Blade guides should be inspected and adjusted after approximately 3 hours of use. Frequent replacement 

of blade guides is recommended to maintain cutting accuracy and extend blade life.

B. Use of Miter Gauge for straight edge or angle cuts

1) Set guide at the desired angle by loosening thumb screw and rotating position mark on the silver bar to 

    desired angle.

2) Tighten screw to secure setting. Place angle guide into the channel on the work surface.

3) Place material against the straight edge guide and feed the material slowly into the blade (Fig.12) pushing back to the 

    guide. The band saw is designed for intricate radius cutting; however the miter gauge will permit straight edge cutting 

    when needed.

C. Blade Tracking

Each

PRECISION 2000™

 is fully tested and adjusted before it is shipped. Occasionally, additional tracking adjustments 

are necessary due to movement in shipping. Ideally the blade should be positioned 1/8” - 1/16” (3.75 - 1.66 mm) from 

the back wall of the upper wheel. 

*Excess tubing can be cut and removed using household scissors.

Fig.7

Fig.8

Fig.9

Содержание Studio Pro Precision 2000









Отзывы: