background image

 

14. 

Cutting Depth Indicator

–Indicates blade’s 

depth from surface. 

15. 

Vernier Throttle

–Increases or decreases 

engine speed. 

16. 

Coolant Temperature Gauge

–Indicates engine 

coolant temperature. 

Note: Check the cooling 

system when the coolant temperature light turns 
on, or when the coolant temperature gauge 
passes the red mark

17. 

Ignition Switch

–Four-position switch activates 

the glow plug, stops the engine, provides power 
to certain accessories, or starts the engine. 

18. 

Engine Warning Light Gauge

–Indicates high 

coolant temperature, low oil pressure, low 
battery voltage, and an energized glow plug. 

19. 

Blade Tachometer/Hour Meter

–Indicates blade 

speed and total number of saw hours operated. 

20. 

Auto Water Switch

–Activates automatic water 

system.  Water turns on/off when depth indicator 
enters 

Auto Water On/Off Zone

21. 

Free Wheel Switch

–Allows operator to move 

saw forward/backward (with ignition switch at 

Run

). 

22. 

Speed Control Lever

–Forward, stop (neutral), 

and reverse control. 

23. 

Control Grip

–Two pushbuttons on front of grip 

raise or lower the saw and blade.  Pushbutton 
on side of grip tilts handlebars, allowing them to 
be moved up or down to desired position. 

24. 

Blade Clutch Switch (optional)

–Allows 

operator to engage or disengage blade rotation. 

25. 

Spotlight Switch

–Activates spotlight. 

26. 

Water Pump Switch (optional)

–Activates water 

pump. 

 
 
 
 

Содержание CC7074













































Отзывы: