background image

2

CONTINUOUS RMS OUTPUT POWER

Note: Full Rated Power is generated at all voltages between 11 and 16VDC.

D7152

D7402

150W x 2 @ 4 Ohm Stereo

400W x 2 @ 4 Ohm Stere

 300W x 2 @ 2 Ohm Stereo

800W x 2 @ 2 Ohm Stereo

 600W Bridged @ 4 Ohms

1600W Bridged @ 4 Ohms

(minimum impedance)

(minimum impedance)

CROSSOVER SPECIFICATIONS

Quantity:

2 (1 for CH 1/2 INPUT, 1 for X-OVER OUT)

Type:

Fully Independent and Selectable Highpass,
Lowpass, Bandpass or All-pass

Slope:

Third Order 18dB/Octave

Alignment:

Butterworth

FUSE RECOMMENDATIONS

D7 Professional Reference Series Amplifiers

, by design, require external fusing.

Research has shown that a circuit board mounted fuse can create a drop in
available DC voltage at the input of the power supply resulting in increased
current draw.

We recommend that you install the correct size fuse/holder combination to the
main power cable within 18 inches of the battery. This will protect your vehicle
from fire damage due to a short circuit to the chassis or vehicle body. If a single
amplifier is installed, follow the fuse recommendation below. If installing
multiple amplifiers, add up the total fuse ratings of all installed amplifiers. This
should be used as your main fuse rating.

Amplifier

Maximum Fuse Rating

D7152

80

D7402

150

Note: A main fuse must be installed within 18 inches of the positive

battery terminal.

19

SYSTEM DIAGRAM 3

Two Channel System

Using a Three-Way Component Set

D7402 two channel amplifier

?

Channels 1/2 full range to a three-way component
set with passive crossovers

D7152 and D7402 manual #135.p65

8/30/2002, 2:36 PM

2

Содержание D7152











Отзывы: