background image

2

CONTINUOUS RMS OUTPUT POWER

Note: Full Rated Power is generated at all voltages between 11 and 16VDC.

D7054

D7104

50W x 4 @ 4 Ohm Stereo

100W x 4 @ 4 Ohm Stereo

100W x 4 @ 2 Ohm Stereo

200W x 4 @ 2 Ohm Stereo

200W x 2 Bridged @ 4 Ohms

400W x 2 Bridged @ 4 Ohms

(minimum impedance)

(minimum impedance)

CROSSOVER SPECIFICATIONS

Quantity:

3 (1 for CH 1/2 INPUT, 1 for CH 3/4 INPUT,
1 for X-OVER OUT)

Type:

Fully Independent and Selectable Highpass,
Lowpass, Bandpass or All-pass.

Slope:

Third Order 18dB/Octave

Alignment:

Butterworth

FUSE RECOMMENDATIONS

D7 Professional Reference Series Amplifiers

, by design, require external fusing.

Research has shown that a circuit board mounted fuse can create a drop in
available DC voltage at the input of the power supply resulting in increased
current draw.

We recommend that you install the correct size fuse/holder combination to the
main power cable within 18 inches of the battery. This will protect your vehicle
from fire damage due to a short circuit to the chassis or vehicle body. If a single
amplifier is installed, follow the fuse recommendation below. If installing
multiple amplifiers, add up the total fuse ratings of all installed amplifiers. This
should be used as your main fuse rating.

Amplifier

Maximum Fuse Rating

D7054

80

D7104

150

Note: A main fuse must be installed within 18 inches of the positive

battery terminal.

19

SYSTEM DIAGRAM 3

Four Way System with

Dual 4 Channel Amplifiers

D7 four channel amplifier

?

Channels 1/2 Highpass to tweeters

?

Channels 3/4 Bandpass to midrange drivers

?

AUX. OUT: Full-range to a
2nd 4 channel amplifier

D7 four channel amplifier

?

Channels 1/2 Bandpass to a pair
of  midbass drivers

?

Channels 3/4 Lowpass to a pair of
bridged 8 Ohm subwoofers

Содержание D7054











Отзывы: