background image

AIRCRAFT

DA 40 NG AMM

Temporary Revision

NLG Inspection & Maintenance

Detail Steps/Work Items

Key Items

(13)

Remove the load from the nose-gear and examine
it. Look specially for more than the usual play.

(14)

Examine the control surfaces. Look specially for:

Correct attachment of the hinges.

Correct attachment of the mass balance to the
structure.

(15)

Examine the leading edge of the wing for damage.

(16)

Examine the area of the spar attachments to the
wing shells. Look specially for cracks.

(17)

Examine the leading edge of the horizontal and
vertical stabilizers for damage.

(18)

Examine the engine mount.

(19)

Examine the engine mount points on the firewall.

(20)

Examine the propeller. Look specially to see if the
propeller has touched the ground.

If the adjustable front seats (OÄM 40-252 or OÄM 40-375) are installed:

WARNING:

DO NOT ENGAGE THE LEVER OR BUTTON FOR THE ADJUSTABLE
BACKREST OF THE FRONT SEATS UNINTENTIONALLY. THE SPRING
LOADED BACKREST MAY SNAP FORWARD AND CAN CAUSE INJURY.

(21)

If the adjustable front seats (OÄM 40-252 or OÄM
40-375) are installed:

Do a test of the backrest adjustment mechanism
on both front seats (refer to Section 25-10).

Doc # 6.02.15
AMM-TR-MÄM 40-1038

05-50-00

Page 14

13 Jul 2020

Содержание AMM-TR-MAM 40-1038























Отзывы: