Diamatic MPS-1027E, Руководство по эксплуатации

Страница: 5 / 11

The Choice of Professionals ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶
̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶ ̶̶̶̶
www.diamatic.usa P a g e | 5 info@diamatic.usa
3. Turning the machine on
•
Insert ̶̶̶̶the ̶̶̶̶safety ̶̶̶̶key ̶̶̶̶and ̶̶̶̶tie ̶̶̶̶the ̶̶̶̶lanyard ̶̶̶̶to ̶̶̶̶operator’s ̶̶̶̶wrist ̶̶̶̶or ̶̶̶̶belt
•
Rotate the e-stop switch
•
Push the remote button on key pad
•
Rotate the motor switch to on position
•
Turn speed control knob to desired rpm displayed on keypad. Recommended rpm range is 1200-1500
4. Turning the machine off
•
To stop the machine turn the motor switch to the off position
•
Press the emergency stop button and disconnect the safety switch key.
•
Turn the speed control knob to 0
5. Disconnecting the machine
•
Follow step 4
•
Turn off power at main control panel
•
Disconnect the plug from the control panel
•
Disconnect power cable from power supply. (this should be done by electrician)
•
Machine is ready for maintenance or storage
4. Maintenance
To keep the machine operating at peak performance, follow the maintenance program of the machine.
Before performing any maintenance, ensure that the machine is disconnected from the power supply and in a zero
mechanical state.
1. After use, unplug the machine immediately.
2. Check the belt, pad driver and pad holder after each use.
3. Use neutral detergent to clean the machine.
4. Check the machine's power cord for damage, if any should be replaced immediately.
5. Monthly waterproof Lubricate wheels, axle.
6. Check for loose or lost nuts, bolts tighten or replace as necessary.
7. After use in dusty environments, remove the motor cover and clean with low pressure air supply to ensure
good ventilation.