background image

DSP-15 User Manual 

Page 16 of 23

DSP15_MAN_C 

5. Installation 

Detector Installation 

Location: 

 The detector should be installed in a weatherproof location that is near the loop.  Ideally, a technician 

should be able to see the loop and the detector at the same time. 

Mounting:

  The detector will function when mounted in any orientation.  It is best to mount the detector such 

that  the  switches  and  indicators  will  be  easily  accessible  for  configuration  and  troubleshooting.    If  using  a 
detector harness, be sure to leave enough of the wiring harness to allow the technician to easily work with the 
detector.

Wiring:

  The detector will come with a 10-pin terminal block or a 10-pin male Molex connector.  Wire nuts can 

be used for most connections to the wires in a detector wiring harness.  However, wire nuts should never be 
used  at  any  point  in  the  loop  circuit  itself.    All  loop  connections  should  be  crimped  or  screw  terminals  at  a 
minimum and soldered for best long-term reliability. 

Wiring Diagram

Pin

Description

1

Output A Relay Common

2

Output A (N.C.)

3

Output A (N.O.)

4

Output B Relay Common

5

Output B (N.O.)

6

No Connection

7

DC Power In

8

DC Power Common

9

Loop

10

Loop

Special  attention  should  be  paid  to  ensure  that  the  loop  wires  remain  tightly  twisted  together.    An  air  gap 
between the two wires for a loop may cause the detector to lock up if the wires are disturbed.

Loop Installation 

The reliability and overall performance of the detector are greatly dependent on the loop itself.  Several factors 
go into a good loop installation: type of wire used, loop configuration, and installation practices. 

Type of Wire Used:

  The wire used for wiring the loop should have a jacket of cross-linked polyethylene. This 

would be a wire with an XLP jacket such as XHHW.  THHN or similar wire types should never be used for loop 
wire.   

The gauge of the wire to use depends on two factors: Distance in cable feet from the loop to the detector and 
stresses the wire may see.  The gauge of the wire can be 20 AWG as long as the detector is within 50 feet of the 
loop in cable distance.  For 50 to 100 feet, use at least 18 AWG wire.  At greater than 100 feet, use a 16 AWG 

Содержание DSP-15
























Отзывы: