DFI KD331-C236/Q170 Скачать руководство пользователя

Страница: 45 / 78

www.d

.com

Chapter 3 BIOS Setup

Chapter 3

Boot

Numlock

Select the power-on state for numlock.

Boot Type

Select the boot type. The options are Dual Boot Type, Legacy Boot Type or UEFI Boot

Type.

If you select “Dual Boot Type” or “UEFI Boot Type”, the “Network Stack”, “PXE Boot

capability”, “USB Boot” and “Quiet Boot” will show up.

If you select “Legacy Boot Type”, “PXE Boot to LAN”, “USB Boot” and “Quiet Boot” will

show up.

Network Stack

This field is used to enable or disable network stack.

PXE Boot capability

Disabled

Suppoort Network Stack

UEFI

IPv4/IPv6

Legacy

Legacy PXE OPROM only

Selects Power-on state for
Numlock

Numlock

Boot Type
Network Stack

PXE Boot capability

USB Boot
Quiet Boot

Main

Advanced

Help

↑

↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←

→



Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Security

Exit

Rev. 5.0

<On>

Boot

Note:

If the boot type is set to UEFI, the method for RAID volume creation will be different.

Please refer to Chapter 5

RAID for more information.

Security

Install or Change the Pass-
word and the length of
password must be greater
than one character.

Current TPM Device
TPM State

Supervisor Password

Set Supervisor Password

Main

Advanced

Help

↑

↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←

→



Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Security

Boot

Exit

Rev. 5.0

<Not Detected >
Not Installed

Not installed

Set Supervisor Password

Set the supervisor’s password and the length of the password must be greater than

one character.

Содержание KD331-C236/Q170















































































Результаты поиска

Содержание KD331-C236/Q170

Отзывы:

Похожие инструкции для KD331-C236/Q170

Бренды по названию

Популярные бренды

DFI KD331-C236/Q170, Руководство пользователя

Результаты поиска

Содержание KD331-C236/Q170

Отзывы:

Похожие инструкции для KD331-C236/Q170

Бренды по названию

Популярные бренды