DFI HU968, Руководство пользователя, Страница: 19 / 86

www.dfi .com Chapter 3 Hardware Installation
19
Chapter 3
Signal Pin# Module Pin Type Pwr Rail /Tolerance HU968 Carrier Board Description
A71
LVDS_A0- A72
A73
LVDS_A1- A74
A75
LVDS_A2- A76
A78
LVDS_A3- A79
LV A81
LVDS_A_CK- A82
B71
LVDS_B0- B72
B73
LVDS_B1- B74
B75
LVDS_B2- B76
B77
LVDS_B3- B78
LV B81
LVDS_B_CK- B82
LVDS_VDD_EN A77 O CMOS 3.3V / 3.3V Connect to enable control of LVDS panel power circuit LVDS panel power enable
LVDS_BKLT_EN B79 O CMOS 3.3V / 3.3V Connect to enable control of LVDS panel backlight power circuit. LVDS panel backlight enable
LVDS_BKLT_CTRL B83 O CMOS 3.3V / 3.3V Connect to brightness control of LVDS panel backlight power circuit. LVDS panel backlight brightness control
LVDS_I2C_CK A83 I/O OD CMOS 3.3V / 3.3V PU 4.7K to 3.3V Connect to DDC clock of LVDS panel I2C clock output for LVDS display use
LVDS_I2C_DAT A84 I/O OD CMOS 3.3V / 3.3V PU 4.7K to 3.3V Connect to DDC data of LVDS panel I2C data line for LVDS display use
Signal Pin# Module Pin Type Pwr Rail /Tolerance HU968 Carrier Board Description
LPC_AD0 B4
LPC_AD1 B5
LPC_AD2 B6
LPC_AD3 B7
LPC_FRAME# B3 O CMOS 3.3V / 3.3V LPC frame indicates the start of an LPC cycle
LPC_DRQ0# B8 PU 10K to 3.3V NC
LPC_DRQ1# B9 PU 10K to 3.3V NC
LPC_SERIRQ A50 I/O CMOS 3.3V / 3.3V PU 10K to 3.3V LPC serial interrupt
LPC_CLK B10 O CMOS 3.3V / 3.3V LPC clock output - 24MHz nominal
Signal Pin# Module Pin Type Pwr Rail /Tolerance HU968 Carrier Board Description
SPI_CS# B97 O CMOS 3.3V Suspend/3.3V Connect to Carrier Board SPI Device CS# pin Chip select for Carrier Board SPI - may be sourced from chipset SPI0 or SPI1
SPI_MISO A92 I CMOS 3.3V Suspend/3.3V Connect a series resistor 33
ȟ
to Carrier Board SPI Device SO pin Data in to Module from Carrier SPI
SPI_MOSI A95 O CMOS 3.3V Suspend/3.3V Connect a series resistor 33
ȟ
to Carrier Board SPI Device SI pin Data out from Module to Carrier SPI
SPI_CLK A94 O CMOS 3.3V Suspend/3.3V Connect a series resistor 33
ȟ
to Carrier Board SPI Device SCK pin Clock from Module to Carrier SPI
SPI_POWER A91 O 3.3V Suspend/3.3V
Power supply for Carrier Board SPI – sourced from Module – nominally
3.3V. The Module shall provide a minimum of 100mA on SPI_POWER.
Carriers shall use less than 100mA of SPI_POWER. SPI_POWER
shall only be used to power SPI devices on the Carrier
BIOS_DIS0# A34
BIOS_DIS1# B88
Connect to LPC device
Connect to LPC device
Selection straps to determine the BIOS boot device.
The Carrier should only float these or pull them low, please refer to
COM Express Module Base Specification Revision 2.1 for strapping options of BIOS disable signals.
LVDS Channel B differential clock
LPC Signals Descriptions
3.3V / 3.3V LPC serial DMA request
SPI Signals Descriptions
O LVDS LVDS
Connect to LVDS connector
O LVDS LVDS
Connect to LVDS connector
I/O CMOS 3.3V / 3.3V
NA
O LVDS LVDS
LVDS
Connect to LVDS connector
O LVDS LVDS
LPC multiplexed address, command and data bus
O LVDS LVDS
Connect to LVDS connector
LVDS Channel B differential pairs
Ther LVDS flat panel differential pairs (LVDS_A[0:3]+/-, LVDS_B[0:3]+/-. LV/-,
LV/-) shall have 100
ƻ
terminations across the pairs at the destination. These
terminations may be on the Carrier Board if the Carrier Board implements a LVDS deserializer
on-board
O LVDS LVDS
Connect to LVDS connector
Connect to LVDS connector
LVDS Channel A differential clock O LVDS LVDS
Connect to LVDS connector
I CMOS
I CMOS
LVDS Signals Descriptions
O LVDS LVDS
Connect to LVDS connector LVDS Channel A differential pairs
Ther LVDS flat panel differential pairs (LVDS_A[0:3]+/-, LVDS_B[0:3]+/-. LV/-,
LV/-) shall have 100
ƻ
terminations across the pairs at the destination. These
terminations may be on the Carrier Board if the Carrier Board implements a LVDS deserializer
on-board
O LVDS
Connect to LVDS connector
O LVDS LVDS
Connect to LVDS connector
Ref
Line
Bios
Entry
SPI
Descriptor
Carrier
SPI_CS#
Chipset
SPI CS0#
Destination
Chipset
SPI CS1#
Destination
BIOS
DIS0#
BIOS
DIS1#
1
1
1
1
0 0
0
0
Module Module SPI0/SPI1
SPI1
(Default)
SPI0
High
High
Carrier Carrier
Carrier
(Default)
Module
(Default)
Module
Module
Module
(Default)
Module
Module Module
3
2
1
0
Carrier FWH
SPI0/SPI1
(Default)
SPI0/SPI1