www.dfi .com
9
Chapter 2 Hardware Installation
Chapter 2
Chapter 2 - Hardware Installation
Board Layout
1
1
SATA 1
SATA 0
1
SATA 5
Clear CMOS Data (JP9)
Power-on
Select (JP10)
1
ATX
Power
Mini PCIe
Mini PCIe Signal
Select (JP15)
Mini PCIe Power Select (JP16)
PCIe x4 (x1 signal)
13
12
24
PS/2 KB/MS Power Select (JP1)
USB 8-9 Power Select (JP4)
COM1 RS232/422/485
Select
COM2 RS232/422/485
Select
COM1 RS232/Power
Select
COM2 RS232/Power
Select
(JP2)
(JP11)
(JP3)
(JP14)
1
1
1 1
1
1
USB 4-5 Power
Select (JP6)
USB 0-1 Power
Select (JP5)
Battery
USB 2-3 Power
Select (JP8)
1
1
1
PS/2 KB/MS
USB 8-9
Buzzer
(JP4)
(JP1)
LAN 1
USB 0-1
USB 4-5
Line-in
Line-out
Mic-in
1
PCI 1
PCI 2
PCIe x16
Socket LGA1150
COM2
COM1
1
2
9
10 USB 2-3
1
3
10
12
SPI Flash
BIOS
SATA 3.0
SATA 2.0
DIO Power
Select
(JP13)
DIO 3/5/7/9
Output State
(JP12)
Chassis
intrusion
1
DIO
2
9
10
1
Front Audio
S/PDIF
1
DVI-I
HDMI
1
2
5
6
1
2
5
6
1
2
5
6
1
2
5
6
(JP11)
+12V
Power
USB 2.0
(JP2)
DDR3_1
DDR3_3
Nuvoton
NCT6102D
ITE
IT8893E
Realtek
ALC886
ASMedia
ASM1442
ASMedia
ASM1442
Intel
WGI210AT
1
12
2
11
(JP14)
COM2
COM1
USB 3.0
USB 2.0
USB 2.0
(JP3)
1
2
19
1
5
4
8
Intel
H81
DIO 11/13/15/17
Output State (JP7)
LAN 2
1
2
10
9
1
2
10
9
COM5
COM6
COM4
COM3
1
2
10
9
1
2
10
9
Intel
WGI217LM
CPU Fan
1
1
1
System Fan 1
1
2
Front Panel
LPC
Standby
Power LED
11
12
System Fan 2
1
2
1
26
25
Parallel
ISL95820
System Memory
DDR3-3
DDR3-1
Standby
Power LED
Features
• Two
240-pin
DDR3/DDR3L DIMM sockets
• Supports
DDR3/DDR3L 1333/1600MHz when operating at 1.5V
•
Supports dual channel memory interface
•
Supports up to 16GB system memory
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lit red, it indicates that there is power on the system
board. Power-off the PC then unplug the power cord prior to installing any devices.
Failure to do so will cause severe damage to the motherboard and components.
Rear I/O
Onboard I/O
Storage
Expansion
•
HD330-H81B has LAN1 only.
•
HD330-H81C: 6 COM (COM1 to COM6).
HD330-H81B/D: 2 COM (COM1 and COM2).
