manualshive.com logo in svg

DFI G5G330-P, Руководство пользователя, Страница: 8 / 117

Поделиться
Скачать
DFI G5G330-P Скачать руководство пользователя страница 8

Introduction

1

8

• CPU stopped clock control
• Microsoft

®

/Intel

®

 APM 1.2 compliant

• Soft Power supported - ACPI v1.0a specification
• AC power failure recovery

Damage Free Intelligence

• Monitors CPU/system temperature and overheat alarm
• Monitors CPU(V), +1.5V, +3.3V, +5V, +12V, -12V, VBAT(V) and

5VSB(V) voltages and  failure alarm

• Monitors CPU/chassis/2nd fan speed and failure alarm
• Read back capability that displays temperature, voltage and fan

speed

• Watchdog timer function

Onboard Graphics Features

• Integrated display interface

-

Analog CRT DAC interface support
-

Supports max DAC frequency up to 400MHz

-

24-bit RAMDAC support

-

Up to 2048x1536 mode support

-

Digital LVDS interface support
-

Integrated dual channel LVDS interface support

-

Suppor ts 25 to 112MHz single/dual channel LVDS
interface

-

Single channel LVDS interface support: 1 x 18 bpp

-

Dual channel LVDS interface support: 2 x 18 bpp

• Internal graphics features

-

DVMT 3.0 support
-

1MB or 8MB of pre-allocated memory supported

-

Intel

®

 Dual-Frequency Graphics Technology

-

Intel

®

 Smart 2D Display Technology

-

Dual Independent display pipes

-

32-bit hardware cursor supported

-

2D graphics engine
-

Optimized 256-bit BLT engine

-

32-bit Alpha blended cursor

Содержание G5G330-P






















































































































Отзывы:

Нет отзывов