DFI CR908-B Скачать руководство пользователя страница 32

www.dfi .com

Chapter 4 BIOS Setup

32

Chapter 4

CPU Configuration

This section is used to configure the CPU. It will also display the detected CPU 

information.

Enabled for Windows XP 
and Linux (OS optimized 
for Hyper-Threading 
Technology) and Disabled 
for other OS (OS not 
optimized for 
Hyper-Threading 
Technology). When 
Disabled only one thread 
per enabled core is 
enabled.

Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.

Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.

CPU Confi guration

Genuine Intel (R) CPU @ 2.30GHz
CPU Signature
Microcode Patch
Max CPU Speed 
Min CPU Speed
CPU Speed
Processor Cores
Intel HT Technology
Intel VT-X Technology
Intel SMX Technology
64 bit

L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache

Hyper-threading

Active Process Core
Limit CUPID Maximum
Intel Virtualization Technology

Advanced

Hyper-threading

Enable this field for Windows XP and Linux which are optimized for Hyper-Threading 

technology. Select disabled for other OSes not optimized for Hyper-Threading tech-

nology. When disabled, only one thread per enabled core is enabled.

Active Process Core

Number of cores to enable in each processor package

Limit CUPID Maximum

The CPUID instruction of some newer CPUs will return a value greater than 3. 

The default is Disabled because this problem does not exist in the Windows series 

operating systems. If you are using an operating system other than Windows, this 

problem may occur. To avoid this problem, enable this field to limit the return value 

to 3 or less than 3

Intel Virtualization Technology

When this field is set to Enabled, the VMM can utilize the additional hardware capa-

bilities provided by Vanderpool Technology.

306a5
7
2300 MHz
1200 MHz
2300 MHz
2
Supported
Supported
Supported
Supported

32 kB x2
32 kB x2
256 kB x2
4096 kB

[Enabled]

[All]
[Disabled]
[Disabled]



 Select Screen



   Select Item

Enter: Select
+/-:   Change Opt.
F1:   General Help
F2: Previous 

Values

F3: 

Optimized  Defaults   

ESC:  Exit

SATA Configuration

This section is used to configure SATA functions.

 

Enable or disable SATA 
Device. 

Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.

Version 2.02.1205. Copyright (C) 2010 American Megatrends, Inc.

SATA Controller(s)

SATA Mode Selection
SATA Controller Speed

Serial ATA Port 0
   Software Preserve
   

Port 0 

   Hot Plug
   External SATA
   SATA Device Type
   Spin Up Device

Serial ATA Port 1
   Software Preserve

   Port 1 
   Hot Plug
   External SATA
   SATA Device Type
   Spin Up Device

Serial ATA Port 2
   Software Preserve
  

 Port 2 

   Hot Plug
   External SATA
   Spin Up Device

Serial ATA Port 3
   Software Preserve
   

Port 3 

   Hot Plug
   External SATA
   Spin Up Device

Serial ATA Port 4
   Software Preserve
   

Port 4 

   Hot Plug
   External SATA
   Spin Up Device

  

Advanced

SATA Controller(s)

This field is used to enable or disable the Serial ATA channels.

SATA Mode Selection

IDE Mode  

This option configures the Serial ATA drives as Parallel ATA storage devices.

AHCI Mode  

This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Inter-

face).

RAID Mode 

This option allows you to create RAID or Intel Matrix Storage configuration on Serial ATA 

devices.

SATA Controller Speed

It indicates the maximun speed which the SATA controller can support.

[Enabled]

[AHCI]
[Gen3]

WDC WD2500BEVS (250.0
Supported

[Enabled]
[Disabled]
[Disabled]
[Hard Disk Driver]
[Disabled]

Empty
Unknown

[Enabled]
[Disabled]
[Disabled]
[Hard Disk Driver]
[Disabled]

ATAPI  iHOS10 ATAPI
N/A

[Enabled]
[Disabled]
[Disabled]
[Disabled]

Empty
Unknown

[Enabled]
[Disabled]
[Disabled]
[Disabled]

GLS85LS1004P (4.0GB
Supported

[Enabled]
[Disabled]
[Disabled]
[Disabled]



 Select Screen



   Select Item

Enter: Select
+/-:   Change Opt.
F1:   General Help
F2: Previous 

Values

F3: Optimized 

Defaults

ESC:  Exit

Содержание CR908-B




































































Отзывы: