DFI 915G-TMGF Скачать руководство пользователя

Страница: 77 / 118

BIOS Setup

3.1.4.2 Onboard Device

Move the cursor to this field and press <Enter>. The following
screen will appear.

The settings on the screen are for reference only. Your version may not be identical
to this one.

USB Controller

Enabled

Enables the onboard USB.

Disabled

Disables the onboard USB.

USB 2.0 Controller

If you are using a USB 2.0 device, this field must be set to Enabled.

USB Keyboard Support

By default, this field is Disabled. However, if you are using a USB
keyboard under DOS, make sure to enable this function.

SATA Port

If the “PATA IDE Mode” field is set to Primary, this field will
show “P1, P3 is Secondary”; meaning SATA 2 and SATA 4 are
Secondary.

If the “PATA IDE Mode” field is set to Secondary, this field will
show “P0, P2 is Primary”; meaning SATA 1 and SATA 3 are
Primary.

Содержание 915G-TMGF























































































































Результаты поиска

Содержание 915G-TMGF

Отзывы:

Похожие инструкции для 915G-TMGF

Бренды по названию

Популярные бренды

DFI 915G-TMGF, Руководство пользователя

Результаты поиска

Содержание 915G-TMGF

Отзывы:

Похожие инструкции для 915G-TMGF

Бренды по названию

Популярные бренды