DFI-ITOX G7VP2 Скачать руководство пользователя

Страница: 61 / 70

Supported Softwares

Important:

Once the utility is installed, the system will ignore the settings in

the System Health Monitor field of the Chipset Features Setup.

If you are using Windows



95/98 or Windows NT



4.0, you may

select between using the utility and the Chipset Features Setup.

For other operating systems, you may only use the Chipset

Features Setup.

4.2.1 Installing the Utility

Insert the CD that came with the system board into a CD-ROM

drive. The autorun screen (Main Board Utility CD) will appear. Click

System Health Monitor Utility. After completing installation, you will

find this utility in StartUp under Programs of Windows



95/98/

NT4.0. Please refer to its Readme file for details on using the utility.

4.3 Drivers

The system board package comes with drivers contained in the

provided CD. For installation instructions or information about their

corresponding readme, click the Read Me button in the autorun

screen.

The autorun screen normally appears after the CD is inserted

into a CD-ROM drive.

All steps or procedures to install software drivers are subject to

change without notice as the softwares are occassionally updated.

Please refer to the readme files for the latest information.

Содержание G7VP2







































































Результаты поиска

Содержание G7VP2

Отзывы:

Похожие инструкции для G7VP2

Бренды по названию

Популярные бренды

DFI-ITOX G7VP2, Руководство пользователя

Результаты поиска

Содержание G7VP2

Отзывы:

Похожие инструкции для G7VP2

Бренды по названию

Популярные бренды