manualshive.com logo in svg

DFE TA500-EIP, Инструкция по эксплуатации, Страница: 9 / 30

Поделиться
Скачать
DFE TA500-EIP Скачать руководство пользователя страница 9

5 

 

 
 
Module Status (MS) LED  

The Module Status LED is a bi-color red/green LED. The state of the LED depends on the state of the network 

adapter module. 

MS LED STATE 

DEFINITION 

OFF 

Power off. 

Steady Green 

Device in operation. 

Flashing Green 

Standby device, not configured, no IP ad-

dress assigned. 

Flashing Red 

Major recoverable fault. 

Steady Red 

Major unrecoverable fault, device not oper-

ational. 

Flashing Green/Red 

Self-test at power on. 

 

Network Status (NS) LED  

The Network Status LED is a bi-color red/green LED. The state of the LED depends on status of the CIP 

(Common Industrial Protocol) connection. 
 

NS LED STATE 

DEFINITION 

OFF 

Power off or no IP address configured. 

Flashing Green 

Device not connected: An IP address is 

configured, but no CIP connections are 

established. 

Steady Green 

Device connected: An IP address is 

configured, at least one CIP connection 

is established. 

Green, 1 flash 

Online (STOP) Connection with IO con-

troller established, IO controller in 

STOP state or IO data bad. 

Green, 3 flashes 

Identify Flashing 3 times (1Hz) continu-

ously to identify slave (DCP Identify). 

Steady Red 

Error: The device has detected that its 

IP address is already in use. 

Red, 2 flashes 

IP address error. 

Red, 3 flashes 

Expected Identification differs from 

Real Identification. 

Flashing Green/Red 

Self-test at power on. 

 

Содержание TA500-EIP































Отзывы:

Нет отзывов