DeZurik PFW Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 12

DeZurik PFW Скачать руководство пользователя страница 4

DeZURIK

2---16" PTW & PFW Tapered Plug Valves

D10188

Page 4

April 2015

Description

The 3-Way (PTW) and 4-Way (PFW) Tapered Plug valves are available with material, actuator and
accessory options to meet a wide range of application requirements.

Three plug styles are offered to provide flow paths with 90 and 360 degree plug rotation. Each different
flow path arrangement has a unique number called a Combination Number. See the Product Bulletin for
these valves for a complete description of the Combination Numbers.

If an actuator other than a DeZURIK is to be mounted, the actuator must be capable of maintaining the
valve plug position with flow in the pipeline.

.

This valve is a pressure vessel. Failure to release pipeline pressure may result in
personal injury and/or flow system damage. Completely release pipeline pressure
before removing the actuator from the valve or removing the valve from the pipeline.

Handling

Lifting the valve improperly may damage it. Do not fasten lifting devices to the

actuator, plug or through

the seat opening in the body. Lift the valve with

slings, chains or cables fastened around the valve

body, or fastened to bolts or

rods through bolt holes in the flanges.

Required Tools

This valve is assembled using only SAE fasteners. To service this valve, you should have a full set of
combination wrenches, Allen wrenches, a large flat tipped screwdriver, a flat pry bar, a pin punch and a
dead blow hammer.

Note:

You may want to machine a shaft to aid you in removing the lower bearing from the body. See

"Disassembly" section.

Installation

This Instruction Manual covers the installation requirements of the valve only. For actuator or accessory
installation information, see the Instruction Manual for that component.

Flow Direction

It is recommended that the valve be installed so pipeline pressure will push the plug into the seat(s) of
the port(s) being sealed.

Lubrication

This valve does not require routine maintenance lubrication. If the valve is disassembled, lubricate the
packing and plug journals as follows:

«
...
2
3
4
5
6
...
»

Содержание PFW













Отзывы:

Нет отзывов