manualshive.com logo in svg

DeZurik PEF, Инструкция по установке и эксплуатации, Страница: 10 / 20

Поделиться
Скачать
DeZurik PEF Скачать руководство пользователя страница 10

DeZURIK

 

3---36" PEF 100% Port Eccentric Plug Valves

 

D10453 

Page 10 

April 2015 

 

Lubrication

 

(Continued) 

Plug Journals 

Plug journal lubrication is dependent upon the materials used in construction of the valve. 

•

  C

AST 

I

RON 

V

ALVES

: Lubricate the journals on the plug using one of these lubricants. 

 

- Lubriplate Clearplex-2  (

recommended

) 

 

- Amoco FG (alternate) 

- Mobilgrease FM 101 (alternate) 

- Petro-Canada Purity FG 2 (alternate) 

 

- Phillips Philube PF (alternate) 

 

Note: 

Ensure lubricant is compatible with flow media. 

Thrust Washers and O-rings 

Apply a light coat to all surfaces of thrust washers and O-rings using one of these lubricants. 

 

- Lubriplate Clearplex-2  (

recommended

) 

 

- Phillips Philube PF (alternate) 

- Mobilgrease FM 101 (alternate) 

 

- Amoco FG (alternate) 

 

Note: 

Ensure lubricant is compatible with flow media. 

Packing Adjustment

 

The stem seal tightening procedure is dependent upon the type of actuator on the valve. If a packing 
leak should occur, tighten the packing as follows: 

3” – 8" Lever and Nut Operated Valves 

Table A: Actuating Torque 

Valve Size 

Actuating Torque 

Standard Packing 

in 

mm 

ft lbs 

Nm 

3 & 4 

100 

28 

37 

5 & 6 

125-150 

60 

81 

8 

200 

104 

141 

All Other Actuators 

Tighten the gland nuts evenly only until the leak stops. 

Note: 

Do not continue tightening after leak stops. If packing leak cannot be stopped by tightening the 

gland nuts, the packing must be replaced. 

 

Содержание PEF





















Отзывы:

Нет отзывов