DeZurik APCO 100SA Скачать руководство пользователя страница 14

Printed in U.S.A.

 

Guarantee 

Products, auxiliaries and parts thereof of DeZURIK, Inc. manufacture are warranted to the original purchaser for a period of twenty-four (24) 
months from date of shipment from factory, against defective workmanship and material, but only if properly installed, operated and serviced 
in accordance with DeZURIK, Inc. recommendations.  Repair or replacement, at our option, for items of DeZURIK, Inc. manufacture will be 
made free of charge, (FOB) our facility with removal, transportation and installation at your cost, if proved to be defective within such time, 
and this is your sole remedy with respect to such products.  Equipment or parts manufactured by others but furnished by DeZURIK, Inc. will 
be repaired or replaced, but only to the extent provided in and honored by the original manufacturers warranty to DeZURIK, Inc., in each 
case subject to the limitations contained therein.  No claim for transportation, labor or special or consequential damages or any other loss, 
cost or damage shall be allowed. You shall be solely responsible for determining suitability for use and in no event shall DeZURIK, Inc. be 
liable in this respect. DeZURIK, Inc. does not guarantee resistance to corrosion, erosion, abrasion or other sources of failure, nor does 
DeZURIK, Inc. guarantee a minimum length of service. Your failure to give written notice to us of any alleged defect under this warranty 
within twenty (20) days of its discovery, or attempts by someone other than DeZURIK, Inc. or its authorized representatives to remedy the 
alleged defects therein, or failure to return product or parts for repair or replacement as herein provided, or failure to install and operate said 
products and parts according to instructions furnished by DeZURIK, Inc., or misuse, modification, abuse or alteration of such  product, 
accident, fire, flood  or other Act of God, or failure to pay entire contract price when due shall be a waiver by you of all rights under this 
warranty.  

The foregoing guarantee shall be null and void if, after shipment from our factory, the item is modified in any way or a component of another 
manufacturer, such as but not limited to, an actuator is attached to the item by anyone other than DeZURIK, Inc. Factory Service personnel. 
All orders accepted shall be deemed accepted subject to this limited warranty, which shall be exclusive of any other or previous Warranty, 
and this shall be the only effective guarantee or warranty binding on DeZURIK, Inc., despite anything to the contrary contained in the 
purchase order or represented by any agent or employee of DeZURIK, Inc., in writing or otherwise, notwithstanding, including but not limited 
to implied warranties.  

THE FOREGOING REPAIR AND REPLACEMENT OBLIGATIONS ARE IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS AND 
LIABILITIES, INCLUDING ALL WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR OF MERCHANTABILITY OR 
OTHERWISE, EXPRESSED OR IMPLIED IN FACT OR BY LAW, AND STATE DEZURIK, INC.’S ENTIRE AND EXCLUSIVE LIABILITY 
AND YOUR EXCLUSIVE REMEDY FOR ANY CLAIM IN CONNECTION WITH THE SALE AND FURNISHING OF SERVICES, GOODS 
OR PARTS, THEIR DESIGN, SUITABILITY FOR USE, INSTALLATION OR OPERATIONS.  

 

Limitation of liability 

LIMITATION OF LIABILITY: IN NO EVENT SHALL DEZURIK, INC. BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL OR 
CONSEQUENTIAL DAMAGES WHATSOEVER, AND DEZURIK, INC.’S LIABILITY, UNDER NO CIRCUMSTANCES, WILL EXCEED THE 
CONTRACT PRICE FOR THE GOODS AND/OR SERVICES FOR WHICH LIABILITY IS CLAIMED. ANY ACTION BY YOU FOR BREACH 
OF CONTRACT MUST BE COMMENCED WITHIN 12 MONTHS AFTER THE DATE OF SALE. 

 

 
 
 
 
 
 

Sales and Service 

For information about our worldwide locations, approvals, certifications and local representative: 

Web site: 

www.dezurik.com

 

E-Mail: 

[email protected]

 

 

250 Riverside Ave. N., Sartel

l, MN 56377 ● Phone: 320

-259-

2000 ● Fax: 320

-259-2227 

DeZURIK, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation. 

Design features, materials of construction and dimensional data, as described in this manual, are provided for your information only 

 and should not be relied upon unless confirmed in writing by DeZURIK, Inc. Certified drawings are available upon request.

 

Содержание APCO 100SA















Отзывы: