background image

Appendix C: IP Address, Subnet and Gateway 

Subnetting and Subnet Masks 

Subnetting divides a network address into sub-network addresses to accommodate 
more than one physical network on a logical network. 
 
For example: 
A Class B company has 100 LANs (Local Area Networks) with 100 to 200 nodes on 
each LAN.    To classify the nodes by its LANs on one main network, this company 
segments the network address into 100 sub-network addresses.    If the Class B 
network address is 150.1.x.x, the address can be segmented further from 150.1.1.x 
through 150.1.100.x 
 
A subnet mask is a 32-bit value that distinguishes the network ID from the host ID for 
different sub-networks on the same logical network.    Like IP addresses, subnet 
masks consist of four octets in dotted decimal notation.    You can use subnet masks 
to route and filter the transmission of IP packets among your sub-networks.    The 
value “255” is assigned to octets that belong to the network ID, and the value “0” is 
assigned to octets that belong to the host ID. 
 
For the example above, if you want all the devices on the sub-networks to receive 
each other’s IP packets, set the subnet mask to 255.255.0.0.    If you want the devices 
on a single sub-network only to receive IP packets from other devices on its own 
sub-network, set the subnet mask to 255.255.255.0 for the devices on the 
sub-network. 
 

Subnet Mask  Routing and Filtering 

0.0.0.0 

IP packets are transmitted to all devices. 

255.0.0.0 

IP packets are only transmitted to devices that are IP that’s first octet 
matches the sender’s IP address’s first octet. 

255.255.0.0 

IP packets are only transmitted to devices that are IP that’s first two 
octets match the sender’s IP address’s first two octets. 

255.255.255.0  IP packets are only transmitted to devices that are IP that’s first three 

octets match the sender’s IP address’s first three octets. 

 

iCAMView  user  manual                                                                                                                -86- 

Содержание IP CAMERA 050862



























































































Отзывы: