36
EngLIsh
D
e
WALT Tool Tag Ready (Fig. E)
Optional Accessory
Your cut-off tool comes with mounting holes
22
and fasteners
for installing a
D
e
WALT
Tool Tag. You will need a T15 bit tip to
install the tag. The
D
e
WALT
Tool Tag is designed for tracking and
locating professional power tools, equipment, and machines
using the
D
e
WALT
Tool Connect™ app. For proper installation of
the
D
e
WALT
Tool Tag refer to the
D
e
WALT
Tool Tag manual.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
Make sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. F)
WARNING:
To reduce the risk of serious personal injury,
ALWAYS
use proper hand position as shown.
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
1
and one hand on the front handle
7
.
Spindle Lock Button (Fig. A, C)
The spindle lock button
10
is used to lock the spindle
21
when
changing accessories.
1. To engage the spindle lock button, remove the battery pack
and make sure trigger switch is in OFF position.
2. Depress the spindle lock button and turn the wheel and
spindle until the lock button engages the spindle.
3. Use supplied wrench
5
to unscrew the spindle nut
17
and remove or mount accessories. Spindle threads are
right hand.
Lock-Off Button (Fig. A)
Your cut-off tool is equipped with a lock-off button
3
. To lock
the trigger switch in the OFF postition, push the lock-off button
from the left side of the tool. To unlock the trigger switch, push
the lock-off button from the right side of the tool.
LED Light (Fig. A)
The LED light
6
will illuminate as a warning when the tool is
being pushed too hard. Continuing to use the tool after the LED
is lit could cause the tool to hot pack or shut down.
To Operate (Fig. A)
CAUTION:
Before attempting to start, grasp tool firmly
with both hands before lifting.
WARNING:
Edge cutting can be performed only with
wheels that are designed and specified for this purpose.
Protect yourself during edge cutting by directing the open
side of the guard toward a surface.
WARNING:
Wheels used for cutting may break or kick
back if they bend or twist while the tool is being used to do
cut-off work.
WARNING:
Do not use edge cutting wheels for surface
grinding applications because these wheels are not
designed for side pressures encountered with surface
grinding. Wheel breakage and injury may result.
1. Grasp main handle
1
and front handle
7
firmly.
2. Line up wheel with material to be cut. Be sure nothing is
near or in line with the wheel.
3. Depress and hold trigger switch
2
then slowly feed wheel
into work with firm pressure. The shoe
12
may be used
to help guide the tool when making cuts. Do not force the
tool. For maximum efficiency and wheel life, keep the wheel
speed high.
4. To stop tool, release trigger switch
2
.
Wet Cut Method (Fig. A, G, H)
CAUTION:
Never use the saw over head. When using
water, limit cutting to the horizontal position to reduce the
risk of water entering the tool.
WARNING:
Wet cut method
is to be used only with a
diamond blade.
1. Attach the water supply to the water inlet
15
.
2. To regulate the water flow, rotate the water valve
13
to
the open position as shown in Figure G. To stop the flow of
water, rotate the water valve to the closed postion as shown
in Figure H.
3. Proceed to cut as described in
To Operate
.
4. After work, disconnect the water supply from the tool.
Applications
WARNING:
NEVER cut magnesium with this tool.
Magnesium particles may ignite causing personal injury.
WARNING:
Cutting concrete must ONLY be done using
the wet cut method.
• 3 mm max. gauge sheet metal
• Concrete, cinder blocks and bricks
• Reinforcing rod; generally under 25.4 mm diameter
• 3 mm diameter concrete wire mesh
• Corrugated floor and ceiling form (concrete forms)
• Electrical conduit 3 mm wall thickness
• 3 mm max. thick structural forms such as channel, angles,
plate, etc.
nOTE:
The cutting of materials heavier than those listed
above are not recommended due to the possibility of
electrical overloading.
Содержание XR Li-Ion Flexvolt DCS690
